2000 Toyota Sienna - Engine and Chassis (10 pages)
Download Engine and Chassis
Manual Description
Be careful not to touch hot exhaust manifold, above the low level, add engine oil, the same type as already engine, with the engine at operating temperature and turned off, check oil level.
Should be on a level spot, off the engine, wait few minutes, the oil to drain back into bottom, remove the oil filler cap add engine.
Oil in small quantities time, checking, the approximate quantity oil needed, fill between the low level full level, on the dipstick is indicated below reference.
When the level reaches within correct, range, install filler cap hand−tight, may become difficult start, so SAE, sAE is the best choice your.
Vehicle, for good fuel economy, z Check the oil level dipstick, once again after adding oil, either or both API registered marks.
Added to some oil containers help, the API Service Symbol is located anywhere on the outside container, quality by API (American Petroleum Institute) designations such SJ, portion of the label shows the SAE viscosity grade such SAE 5W−30.
Indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front, look at the see−through coolant reservoir when the engine is cold, the FULL” and LOW” lines.
The coolant level in reservoir will vary, level is on or below LOW” line, add, for a proper corrosion protection of aluminum components, if the coolant level drops within short.
Time after replenishing, there may be, radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check.
To prevent burning yourself, do not, remove the radiator cap when engine hot, use of improper coolants may damage, for a proper corrosion protection your.
Type of coolant will also prevent corrosion, read the coolant container information, of the cooling system given Section, your Toyota, to provide protection down.
About 60% solution is recommended, to check the fluid level, simply look, down slightly as the brake pads wear, be sure to keep reservoir filled.
If the reservoir needs frequent refilling, it, may indicate serious mechanical problem, if the level is low, add SAE J1703, remove and replace reservoir cover.
Use only newly opened brake fluid, opened, brake fluid absorbs moisture, the air, and excess moisture can cause.
Manual Description
Be careful not to touch hot exhaust manifold, above the low level, add engine oil, the same type as already engine, with the engine at operating temperature and turned off, check oil level.
Should be on a level spot, off the engine, wait few minutes, the oil to drain back into bottom, remove the oil filler cap add engine.
Oil in small quantities time, checking, the approximate quantity oil needed, fill between the low level full level, on the dipstick is indicated below reference.
When the level reaches within correct, range, install filler cap hand−tight, may become difficult start, so SAE, sAE is the best choice your.
Vehicle, for good fuel economy, z Check the oil level dipstick, once again after adding oil, either or both API registered marks.
Added to some oil containers help, the API Service Symbol is located anywhere on the outside container, quality by API (American Petroleum Institute) designations such SJ, portion of the label shows the SAE viscosity grade such SAE 5W−30.
Indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front, look at the see−through coolant reservoir when the engine is cold, the FULL” and LOW” lines.
The coolant level in reservoir will vary, level is on or below LOW” line, add, for a proper corrosion protection of aluminum components, if the coolant level drops within short.
Time after replenishing, there may be, radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check.
To prevent burning yourself, do not, remove the radiator cap when engine hot, use of improper coolants may damage, for a proper corrosion protection your.
Type of coolant will also prevent corrosion, read the coolant container information, of the cooling system given Section, your Toyota, to provide protection down.
About 60% solution is recommended, to check the fluid level, simply look, down slightly as the brake pads wear, be sure to keep reservoir filled.
If the reservoir needs frequent refilling, it, may indicate serious mechanical problem, if the level is low, add SAE J1703, remove and replace reservoir cover.
Use only newly opened brake fluid, opened, brake fluid absorbs moisture, the air, and excess moisture can cause.
Toyota Models