2001 Toyota RAV4 - 2000-2008 Toyota Various Models TVIP V3 RS3200 System Programming Instructions (10 pages)
Download 2000-2008 Toyota Various Models TVIP V3 RS3200 System Programming Instructions
Manual Description
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM, pASSIVE ARMING ON/ OFF SELECTION AND, for factory remote keyless entry system programming information, refer, refer to the RS3000 Owner's guide RS3000 feature programming.
Follow this procedure to add additional remote controls to a system, operate with a maximum of four remote controls, in the default operation mode (press the UNLOCK button twice to unlock all doors no AUX button, function on button remote controls); to change the operation mode, you must perform separate.
REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 7, the tail and marker lights flash 1 time, the buzzer chirps 1 time doors, * If the system does not activate the lights, buzzer and door locks 1 time, start over.
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM (continued), program (add) an additional remote control, the buzzer chirps 1 time, doors, note: Repeat the above steps to add additional remote controls.
* If the system activates the lights, buzzer and door locks 2 times, start over, follow this procedure to clear all existing remote control codes and reprogram existing remote controls, (press the UNLOCK button twice to unlock all doors and no AUX button function 4 button remote, controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION.
SELECT procedure as shown on pages 6 7, open the driver's door and remove key, start the programming procedure: (Complete these steps within 40 seconds, the tail and marker lights flash 2 times, buzzer.
Chirps times and the doors lock unlock 2 times, *If the system does not activate the lights, buzzer and door locks 2 times, start over, buzzer chirps time, doors lock, note: Repeat the above steps to program (add) additional remote controls.
Follow this procedure to change the operating functions of remote controls already programmed into, button once causes all doors to unlock at the same time, open the driver's door remove key, the tail and marker lights flash 4 times.
The buzzer chirps 4 times doors, * If the system does not activate the lights, buzzer and door locks 4 times, start over, select the operating functions for an existing remote control, buttons on one remote control same time.
Buzzer chirps time, dorrs lock, note: Repeat the above steps select operating, * Program for 4 button remote controls, only, if the system activates the lights, buzzer and door locks 2 times, start over.
Follow this procedure to clear all remote controls programmed to operate the system, have remote controls to program into the system and you want to first clear all existing remote controls, from the system, follow the reprogram procedure as shown on pages 4 5, the tail and marker lights flash 5 times.
Buzzer chirps times and doors lock, * If the system does not activate the lights, buzzer and door locks 5 times, start over, pASSIVE ARMING ON/ OFF SELECTION AND ENTRY DELAY TIME SELECTION, the is factory set to not passively arm.
As well as to adjust the entry delay time, follow procedure below, close all the doors and the trunk or hatch, unlock all the doors with inside, lock switch, then remove the key ignition switch, select the operating mode and entry time delay, complete.
When all doors are closed, the RS3200 is factory set to automatically lock the vehicle's door when, ignition key is turned to ON or START, and unlock them (open or not) when the key turned back, from LOCK ON 5 times.
Manual Description
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM, pASSIVE ARMING ON/ OFF SELECTION AND, for factory remote keyless entry system programming information, refer, refer to the RS3000 Owner's guide RS3000 feature programming.
Follow this procedure to add additional remote controls to a system, operate with a maximum of four remote controls, in the default operation mode (press the UNLOCK button twice to unlock all doors no AUX button, function on button remote controls); to change the operation mode, you must perform separate.
REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 7, the tail and marker lights flash 1 time, the buzzer chirps 1 time doors, * If the system does not activate the lights, buzzer and door locks 1 time, start over.
ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM (continued), program (add) an additional remote control, the buzzer chirps 1 time, doors, note: Repeat the above steps to add additional remote controls.
* If the system activates the lights, buzzer and door locks 2 times, start over, follow this procedure to clear all existing remote control codes and reprogram existing remote controls, (press the UNLOCK button twice to unlock all doors and no AUX button function 4 button remote, controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION.
SELECT procedure as shown on pages 6 7, open the driver's door and remove key, start the programming procedure: (Complete these steps within 40 seconds, the tail and marker lights flash 2 times, buzzer.
Chirps times and the doors lock unlock 2 times, *If the system does not activate the lights, buzzer and door locks 2 times, start over, buzzer chirps time, doors lock, note: Repeat the above steps to program (add) additional remote controls.
Follow this procedure to change the operating functions of remote controls already programmed into, button once causes all doors to unlock at the same time, open the driver's door remove key, the tail and marker lights flash 4 times.
The buzzer chirps 4 times doors, * If the system does not activate the lights, buzzer and door locks 4 times, start over, select the operating functions for an existing remote control, buttons on one remote control same time.
Buzzer chirps time, dorrs lock, note: Repeat the above steps select operating, * Program for 4 button remote controls, only, if the system activates the lights, buzzer and door locks 2 times, start over.
Follow this procedure to clear all remote controls programmed to operate the system, have remote controls to program into the system and you want to first clear all existing remote controls, from the system, follow the reprogram procedure as shown on pages 4 5, the tail and marker lights flash 5 times.
Buzzer chirps times and doors lock, * If the system does not activate the lights, buzzer and door locks 5 times, start over, pASSIVE ARMING ON/ OFF SELECTION AND ENTRY DELAY TIME SELECTION, the is factory set to not passively arm.
As well as to adjust the entry delay time, follow procedure below, close all the doors and the trunk or hatch, unlock all the doors with inside, lock switch, then remove the key ignition switch, select the operating mode and entry time delay, complete.
When all doors are closed, the RS3200 is factory set to automatically lock the vehicle's door when, ignition key is turned to ON or START, and unlock them (open or not) when the key turned back, from LOCK ON 5 times.
Toyota Models