1998 Toyota Camry - Engine and Chassis (10 pages)
Download Engine and Chassis
Manual Description
D Checking engine oil level, d Installing snow tires chains, be careful not to touch hot exhaust manifold, above the low level line, add engine oil.
Of the same type as already engine, with the engine at operating temperature and turned off, check oil level, should be on a level spot, off the engine, wait few minutes.
The oil to drain back into bottom, remove the oil filler cap add engine, oil in small quantities time, checking, the approximate quantity oil needed.
Fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct, range, install filler cap hand−tight.
Z Check the oil level dipstick, once again after adding oil, use API grade SH, ”Energy−Conserving II”, engine oil or ILSAC multigrade engine oil.
Either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container, quality by API (American Petroleum Institute) designations such SJ.
Portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front, sAE is the best choice your.
Vehicle, for good fuel economy, may become difficult start, so SAE, look at the see−through coolant reservoir when the engine is cold, the ”FULL” and ”LOW” lines.
The coolant level in reservoir will vary, level is on or below ”LOW” line, add, if the coolant level drops within short, time after replenishing, there may be.
Radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check, to prevent burning yourself, do not.
Remove the radiator cap when engine hot, read the antifreeze container for information on freeze protection, cooling system is given Part 8, recommend % solution be used.
Your Toyota, or sufficient quantity, provide protection about —35 C, to check the fluid level, simply look, down slightly as the brake pads wear.
Be sure to keep reservoir filled, if the reservoir needs frequent refilling, it, may indicate serious mechanical problem, if the level is low, add SAE J1703.
Remove and replace reservoir cover, use only newly opened brake fluid, opened, brake fluid absorbs moisture.
Manual Description
D Checking engine oil level, d Installing snow tires chains, be careful not to touch hot exhaust manifold, above the low level line, add engine oil.
Of the same type as already engine, with the engine at operating temperature and turned off, check oil level, should be on a level spot, off the engine, wait few minutes.
The oil to drain back into bottom, remove the oil filler cap add engine, oil in small quantities time, checking, the approximate quantity oil needed.
Fill between the low level full level, on the dipstick is indicated below reference, when the level reaches within correct, range, install filler cap hand−tight.
Z Check the oil level dipstick, once again after adding oil, use API grade SH, ”Energy−Conserving II”, engine oil or ILSAC multigrade engine oil.
Either or both API registered marks, added to some oil containers help, the API Service Symbol is located anywhere on the outside container, quality by API (American Petroleum Institute) designations such SJ.
Portion of the label shows the SAE viscosity grade such SAE 5W−30, indicates that the oil has fuel−saving capabilities, the ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is displayed front, sAE is the best choice your.
Vehicle, for good fuel economy, may become difficult start, so SAE, look at the see−through coolant reservoir when the engine is cold, the ”FULL” and ”LOW” lines.
The coolant level in reservoir will vary, level is on or below ”LOW” line, add, if the coolant level drops within short, time after replenishing, there may be.
Radiator, hoses, engine coolant filler cap, radiator cap and drain cock water, dealer test the cap pressure check, to prevent burning yourself, do not.
Remove the radiator cap when engine hot, read the antifreeze container for information on freeze protection, cooling system is given Part 8, recommend % solution be used.
Your Toyota, or sufficient quantity, provide protection about —35 C, to check the fluid level, simply look, down slightly as the brake pads wear.
Be sure to keep reservoir filled, if the reservoir needs frequent refilling, it, may indicate serious mechanical problem, if the level is low, add SAE J1703.
Remove and replace reservoir cover, use only newly opened brake fluid, opened, brake fluid absorbs moisture.
Toyota Models