2010 Nissan Xterra - Road Wheels & Tires (Section WT) (50 pages)
Download Road Wheels & Tires (Section WT)
Manual Description
Wiring Diagram - TIRE PRESSURE MONITORING SYSTEM -30, - C1720 - C1723, C1724 C1727 TRANSMITTER MALFUNCTION16, low Tire Pressure Warning Lamp Does Not Come, on When Ignition Switch Is Turned On36.
Low Tire Pressure Warning Lamp Stays On When, low Tire Pressure Warning Lamp Flashes When, ignition Switch Is Turned On 38, hazard Warning Lamps Flash When Ignition.
ID REGISTRATION CANNOT BE COMPLETED 40, iD Registration Cannot Be Completed 40, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 41, interview the customer to obtain detailed information about symptom.
Repair or replace applicable parts, check the low tire pressure warning lamp, >> Adjust tire pressures specified value, check low tire pressure warning lamp activation.
Does the low tire pressure warning lamp activate for one second when ignition switch turned ON, >> GO TO WT-36, "Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is, are BCM connectors damaged loose, yES >> Repair replace damaged parts.
Check battery transmitter activation tool, is transmitter activation tool battery fully charged, >> Replace battery transmitter activation tool, this procedure must be done after replacement of a low tire pressure warning transmitter BCM.
New replacement transmitters are provided asleep and must first be woken up using Transmitter Activation Tool J-45295 before ID registration can be performed, against the tire near the front left transmitter, repeat this procedure for each tire in the following order: FL, FR, RR, RL, flashing indicator status by CAN according to following time chart.
After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out, iD REGISTRATION WITH TRANSMITTER ACTIVATION TOOL, register the IDs in order from FR LH, FR RH, RR RH and RR LH, been completed, the hazard warning lamps flash.
Be sure to register all of the IDs in order from FR LH, FR RH, RR RH, to RR LH, self-diagnostic results, iD REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL, after completing all ID registrations, press END complete procedure, inflate all tires to proper pressure.
On for second after ignition ON, tire less than 193 kPa (2, low tire pressure warning system malfunction, after key ON, flashes once per second for 1 minute, then stays ON.
A sensor-transmitter integrated with a valve installed each, wheel, and transmits a detected air pressure signal in form, the remote keyless entry receiver is shown with instrument, air pressure signal transmitted by the transmitter each wheel.
The combination meter receives tire pressure status BCM, sensed by the BCM, the combination meter low tire pressure warning lamp activated, the tire pressure warning check connector can be grounded order, to initiate self-diagnosis without a CONSULT-III.
Check connector is located behind the lower portion of instrument panel LH, remote keyless entry receiver M120 5, cONSULT-III can display each diagnostic item using the diagnostic test modes shown following, bCM part number can be read.
Displays BCM input/output data real time, operation of electrical loads can be checked by sending drive signal them, for setting the status suitable for required operation, input/output signals are received from the BCM and received data displayed.
Manual Description
Wiring Diagram - TIRE PRESSURE MONITORING SYSTEM -30, - C1720 - C1723, C1724 C1727 TRANSMITTER MALFUNCTION16, low Tire Pressure Warning Lamp Does Not Come, on When Ignition Switch Is Turned On36.
Low Tire Pressure Warning Lamp Stays On When, low Tire Pressure Warning Lamp Flashes When, ignition Switch Is Turned On 38, hazard Warning Lamps Flash When Ignition.
ID REGISTRATION CANNOT BE COMPLETED 40, iD Registration Cannot Be Completed 40, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 41, interview the customer to obtain detailed information about symptom.
Repair or replace applicable parts, check the low tire pressure warning lamp, >> Adjust tire pressures specified value, check low tire pressure warning lamp activation.
Does the low tire pressure warning lamp activate for one second when ignition switch turned ON, >> GO TO WT-36, "Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is, are BCM connectors damaged loose, yES >> Repair replace damaged parts.
Check battery transmitter activation tool, is transmitter activation tool battery fully charged, >> Replace battery transmitter activation tool, this procedure must be done after replacement of a low tire pressure warning transmitter BCM.
New replacement transmitters are provided asleep and must first be woken up using Transmitter Activation Tool J-45295 before ID registration can be performed, against the tire near the front left transmitter, repeat this procedure for each tire in the following order: FL, FR, RR, RL, flashing indicator status by CAN according to following time chart.
After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out, iD REGISTRATION WITH TRANSMITTER ACTIVATION TOOL, register the IDs in order from FR LH, FR RH, RR RH and RR LH, been completed, the hazard warning lamps flash.
Be sure to register all of the IDs in order from FR LH, FR RH, RR RH, to RR LH, self-diagnostic results, iD REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL, after completing all ID registrations, press END complete procedure, inflate all tires to proper pressure.
On for second after ignition ON, tire less than 193 kPa (2, low tire pressure warning system malfunction, after key ON, flashes once per second for 1 minute, then stays ON.
A sensor-transmitter integrated with a valve installed each, wheel, and transmits a detected air pressure signal in form, the remote keyless entry receiver is shown with instrument, air pressure signal transmitted by the transmitter each wheel.
The combination meter receives tire pressure status BCM, sensed by the BCM, the combination meter low tire pressure warning lamp activated, the tire pressure warning check connector can be grounded order, to initiate self-diagnosis without a CONSULT-III.
Check connector is located behind the lower portion of instrument panel LH, remote keyless entry receiver M120 5, cONSULT-III can display each diagnostic item using the diagnostic test modes shown following, bCM part number can be read.
Displays BCM input/output data real time, operation of electrical loads can be checked by sending drive signal them, for setting the status suitable for required operation, input/output signals are received from the BCM and received data displayed.
Nissan Models