2004 Nissan X-Trail - Seat Belt System (Section SB) (24 pages)
Download Seat Belt System (Section SB)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, precaution for Seat Belt Service 2, removal and Installation of Front Seat Belt 3, removal and Installation of Rear Seat Belt 4.
REMOVAL/WITH TYPE REAR CENTER SEAT BELT 4, component Parts and Harness Connector Location 6, sEAT BELT WARNING CHIME AND SEAT BELT, time Chart for Seat Belt Warning Lamp Chime 7.
Wiring Diagram —S/WARN—/For LHD models 9, wiring Diagram —S/WARN—/For RHD models 12, terminal and Reference Value for Time Control Unit 15, trouble Diagnosis Chart by Symptom 16.
Time Control Unit Power Supply Ground Circuit, seat Belt Warning Lamp Power Supply Check 17, seat Belt Warning Lamp Check (Driver side) 17, seat belt Warning Lamp Check (Passenger Side) 19.
Seat Belt Buckle Switch Check 20, seat Belt Buckle Switch Seat Pressure Switch, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Before removing the seat belt pre-tensioner assembly, turn the ignition switch off, disconnect, both battery cables and wait least 3 minutes, do not use electrical test equipment for seat belt pre-tensioner connector, after replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-tensioner connector, check the system function.
Do not use disassemble buckle seat belt assembly, replace anchor bolts if they are deformed worn out, if any component of seat belt assembly is questionable, do not repair, if webbing is cut, frayed, or damaged, replace seat belt assembly.
When replacing seat belt assembly, use a genuine seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision, nISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly, could result in serious personal injury in an accident.
Should be replaced even if the seat belts are not in use during a frontal collision in which air bags, replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors, buckles show no damage and continue operate properly).
The seat belt was damaged in an accident, the seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly, anchor bolts are deformed worn out.
The seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision, which the air bags deployed, removal and Installation Front Seat Belt, before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait least 3 SB.
Remove pre-tensioner seat belt retractor fixing screws to remove seat belt assembly, remove screw, and remove seat cushion inner finisher, remove anchor bolt to remove seat belt buckle, before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait least 3.
Install in the reverse order removal, removal and Installation Rear Seat Belt, rEMOVAL/WITH TYPE REAR CENTER SEAT BELT.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, precaution for Seat Belt Service 2, removal and Installation of Front Seat Belt 3, removal and Installation of Rear Seat Belt 4.
REMOVAL/WITH TYPE REAR CENTER SEAT BELT 4, component Parts and Harness Connector Location 6, sEAT BELT WARNING CHIME AND SEAT BELT, time Chart for Seat Belt Warning Lamp Chime 7.
Wiring Diagram —S/WARN—/For LHD models 9, wiring Diagram —S/WARN—/For RHD models 12, terminal and Reference Value for Time Control Unit 15, trouble Diagnosis Chart by Symptom 16.
Time Control Unit Power Supply Ground Circuit, seat Belt Warning Lamp Power Supply Check 17, seat Belt Warning Lamp Check (Driver side) 17, seat belt Warning Lamp Check (Passenger Side) 19.
Seat Belt Buckle Switch Check 20, seat Belt Buckle Switch Seat Pressure Switch, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed.
Before removing the seat belt pre-tensioner assembly, turn the ignition switch off, disconnect, both battery cables and wait least 3 minutes, do not use electrical test equipment for seat belt pre-tensioner connector, after replacing or reinstalling seat belt pre-tensioner assembly, or reconnecting seat belt pre-tensioner connector, check the system function.
Do not use disassemble buckle seat belt assembly, replace anchor bolts if they are deformed worn out, if any component of seat belt assembly is questionable, do not repair, if webbing is cut, frayed, or damaged, replace seat belt assembly.
When replacing seat belt assembly, use a genuine seat belt assembly, inspect all seat belt assemblies including retractors and attaching hardware after any collision, nISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate properly, could result in serious personal injury in an accident.
Should be replaced even if the seat belts are not in use during a frontal collision in which air bags, replace any seat belt assembly (including anchor bolts) if, the seat belt was in use at the time of a collision (except for minor collisions and belts, retractors, buckles show no damage and continue operate properly).
The seat belt was damaged in an accident, the seat belt attaching point was damaged in an accident, or distortion and repair as necessary before installing a new seat belt assembly, anchor bolts are deformed worn out.
The seat belt pre-tensioner should be replaced even if the seat belts are not in use during collision, which the air bags deployed, removal and Installation Front Seat Belt, before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait least 3 SB.
Remove pre-tensioner seat belt retractor fixing screws to remove seat belt assembly, remove screw, and remove seat cushion inner finisher, remove anchor bolt to remove seat belt buckle, before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait least 3.
Install in the reverse order removal, removal and Installation Rear Seat Belt, rEMOVAL/WITH TYPE REAR CENTER SEAT BELT.
Nissan Models