2001 Nissan X-Trail - Lighting System (Section LT) (68 pages)
Download Lighting System (Section LT)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, wiring Diagrams Trouble Diagnosis 3, wiring Diagram — H/LAMP — 5, hEADLAMP - DAYTIME LIGHT SYSTEM - 9.
TURN SIGNAL AND HAZARD WARNING LAMPS 17, wiring Diagram — TURN — 19, removal and Installation for Front Turn Signal Lamp 22, removal and Installation for Side Turn Signal Lamp 23.
Removal and Installation for Rear Turn Signal Lamp 23, lIGHTING AND TURN SIGNAL SWITCH 24, wiring Diagram — STOP/L — 26, wiring Diagram — BACK/L — 28.
PARKING, LICENSE PLATE AND TAIL LAMPS 30, wiring Diagram — TAIL/L — 30, wiring Diagram — F/FOG — 34, wiring Diagram -R/FOG-/Without Front Fog Lamp 37.
Wiring Diagram -R/FOG-/With Front Fog Lamp 38, removal and Installation Clearance Lamp 40, removal and Installation Taillamp 40, interior Room Lamp Timer Does Not Operate59.
Interior Room Lamp Timer Does Not Cancel62, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, do not touch the glass of bulb directly by hand.
Touch bulb by hand while it is lit or right after being turned off, do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc, adjust aiming by tightening aiming screw, and then make adjustment by tightening.
To remove soil or sealant of bulbs, do not use organic solvent (thinner, gasoline, etc, when replacing bulb, be sure to hold bulb socket and pull it out straight, pulled at an angle, the bulb may be caught in the lamp, making it difficult take out, when you read wiring diagrams, refer followings.
Refer to "How to Read Wiring Diagrams" GI section, refer to "POWER SUPPLY ROUTING" for power distribution circuit PG section, when you perform trouble diagnosis, refer followings, refer to "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" GI section.
Refer "How to Perform Efficient Diagnosis for an Electrical Incident" GI section, sMA for models with roof mounted driving lamp, the headlamps are controlled by the lighting switch which is built into combination switch, power is supplied all times.
When the lighting switch is turned to the 2ND position and placed in LOW (B”) position, power supplied, terminal of each headlamp supplies ground through body grounds E24 E50, with power and ground supplied, the low beams will illuminate, when the lighting switch is turned to the 2ND position and placed in HIGH (A”) position or PASS (C”) position, power supplied.
To combination meter terminal 61 (LHD models) or 50 (RHD models) for HIGH BEAM indicator, ground is supplied to terminal 60 (LHD models) or 49 (RHD models) of the combination meter through body, ground is supplied to terminal 2 of each headlamp through body grounds E24 E50, with power and ground supplied, the high beams and the HIGH BEAM indicator illuminate.
High beam LH do not operate, but low, terminal and headlamp LH terminal 1, low beam LH does not operate, but high.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, wiring Diagrams Trouble Diagnosis 3, wiring Diagram — H/LAMP — 5, hEADLAMP - DAYTIME LIGHT SYSTEM - 9.
TURN SIGNAL AND HAZARD WARNING LAMPS 17, wiring Diagram — TURN — 19, removal and Installation for Front Turn Signal Lamp 22, removal and Installation for Side Turn Signal Lamp 23.
Removal and Installation for Rear Turn Signal Lamp 23, lIGHTING AND TURN SIGNAL SWITCH 24, wiring Diagram — STOP/L — 26, wiring Diagram — BACK/L — 28.
PARKING, LICENSE PLATE AND TAIL LAMPS 30, wiring Diagram — TAIL/L — 30, wiring Diagram — F/FOG — 34, wiring Diagram -R/FOG-/Without Front Fog Lamp 37.
Wiring Diagram -R/FOG-/With Front Fog Lamp 38, removal and Installation Clearance Lamp 40, removal and Installation Taillamp 40, interior Room Lamp Timer Does Not Operate59.
Interior Room Lamp Timer Does Not Cancel62, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, do not touch the glass of bulb directly by hand.
Touch bulb by hand while it is lit or right after being turned off, do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc, adjust aiming by tightening aiming screw, and then make adjustment by tightening.
To remove soil or sealant of bulbs, do not use organic solvent (thinner, gasoline, etc, when replacing bulb, be sure to hold bulb socket and pull it out straight, pulled at an angle, the bulb may be caught in the lamp, making it difficult take out, when you read wiring diagrams, refer followings.
Refer to "How to Read Wiring Diagrams" GI section, refer to "POWER SUPPLY ROUTING" for power distribution circuit PG section, when you perform trouble diagnosis, refer followings, refer to "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" GI section.
Refer "How to Perform Efficient Diagnosis for an Electrical Incident" GI section, sMA for models with roof mounted driving lamp, the headlamps are controlled by the lighting switch which is built into combination switch, power is supplied all times.
When the lighting switch is turned to the 2ND position and placed in LOW (B”) position, power supplied, terminal of each headlamp supplies ground through body grounds E24 E50, with power and ground supplied, the low beams will illuminate, when the lighting switch is turned to the 2ND position and placed in HIGH (A”) position or PASS (C”) position, power supplied.
To combination meter terminal 61 (LHD models) or 50 (RHD models) for HIGH BEAM indicator, ground is supplied to terminal 60 (LHD models) or 49 (RHD models) of the combination meter through body, ground is supplied to terminal 2 of each headlamp through body grounds E24 E50, with power and ground supplied, the high beams and the HIGH BEAM indicator illuminate.
High beam LH do not operate, but low, terminal and headlamp LH terminal 1, low beam LH does not operate, but high.
Nissan Models