2012 Nissan Versa - Brake System (Section BR) (45 pages)
Download Brake System (Section BR)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 3, dISC ROTOR : Inspection Adjustment15, bRAKE LINING : Inspection Adjustment17.
BRAKE DRUM : Inspection Adjustment17, bRAKE BOOSTER AND CHECK VALVE 30, bRAKE PAD : Inspection Adjustment 15, bRAKE PAD : Exploded View 35.
BRAKE PAD : Removal Installation 35, bRAKE CALIPER ASSEMBLY : Exploded View 36, bRAKE CALIPER ASSEMBLY : Removal Installation 37, bRAKE CALIPER ASSEMBLY : Disassembly.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along C, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc prevent damage, clean any dust from the front brake and rear brake with a vacuum dust collector, brake fluid use refer to MA-12, "Fluids Lubricants", never reuse drained brake fluid.
Never spill or splash brake fluid on painted surfaces, immediately and wash with water if it gets painted surface, always confirm the specified tightening torque when installing brake pipes, after pressing the brake pedal more deeply or harder than normal driving, such as air bleeding, check each.
Always clean with new brake fluid when cleaning the brake caliper other components, never use mineral oils such as gasoline or light oil to clean, always loosen the brake tube flare nut with flare nut wrench, tighten the brake tube flare nut to the specified torque with a crowfoot (A) torque wrench (B).
Brake system is an important safety part, detected, always disassemble the affected part, detected, replace part with new one, always connect the battery terminals when moving vehicle.
Turn the ignition switch OFF and disconnect hydraulic booster, assembly harness connector or battery negative terminal, check that no brake fluid leakage is present after replacing, burnish the brake contact surfaces after refinishing replacing.
Rotors, after replacing pads, or if a soft pedal occurs very low mileage, - Front brake pad: Refer to BR-15, "BRAKE PAD : Inspection Adjustment", - Front disc rotor: Refer to BR-15, "DISC ROTOR : Inspection Adjustment", - Rear brake lining: refer to BR-17, "BRAKE LINING : Inspection Adjustment".
- Rear brake drum: BR-17, "BRAKE DRUM : Inspection Adjustment", the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, brake and clutch pedal height measurement tool.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 3, dISC ROTOR : Inspection Adjustment15, bRAKE LINING : Inspection Adjustment17.
BRAKE DRUM : Inspection Adjustment17, bRAKE BOOSTER AND CHECK VALVE 30, bRAKE PAD : Inspection Adjustment 15, bRAKE PAD : Exploded View 35.
BRAKE PAD : Removal Installation 35, bRAKE CALIPER ASSEMBLY : Exploded View 36, bRAKE CALIPER ASSEMBLY : Removal Installation 37, bRAKE CALIPER ASSEMBLY : Disassembly.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along C, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc prevent damage, clean any dust from the front brake and rear brake with a vacuum dust collector, brake fluid use refer to MA-12, "Fluids Lubricants", never reuse drained brake fluid.
Never spill or splash brake fluid on painted surfaces, immediately and wash with water if it gets painted surface, always confirm the specified tightening torque when installing brake pipes, after pressing the brake pedal more deeply or harder than normal driving, such as air bleeding, check each.
Always clean with new brake fluid when cleaning the brake caliper other components, never use mineral oils such as gasoline or light oil to clean, always loosen the brake tube flare nut with flare nut wrench, tighten the brake tube flare nut to the specified torque with a crowfoot (A) torque wrench (B).
Brake system is an important safety part, detected, always disassemble the affected part, detected, replace part with new one, always connect the battery terminals when moving vehicle.
Turn the ignition switch OFF and disconnect hydraulic booster, assembly harness connector or battery negative terminal, check that no brake fluid leakage is present after replacing, burnish the brake contact surfaces after refinishing replacing.
Rotors, after replacing pads, or if a soft pedal occurs very low mileage, - Front brake pad: Refer to BR-15, "BRAKE PAD : Inspection Adjustment", - Front disc rotor: Refer to BR-15, "DISC ROTOR : Inspection Adjustment", - Rear brake lining: refer to BR-17, "BRAKE LINING : Inspection Adjustment".
- Rear brake drum: BR-17, "BRAKE DRUM : Inspection Adjustment", the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, brake and clutch pedal height measurement tool.
Nissan Models