2010 Nissan Sentra - Engine L System (Section Lu) (27 pages)
Download Engine L System (Section Lu)
Manual Description
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"12, precaution Necessary for Steering Wheel Rotation After Battery Disconnect12, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM).
Remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, if DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, maximum measuring range: 2,452 kPa (25, adapting oil pressure gauge oil pan (upper), removing and installing oil pressure switch.
Before starting engine, park vehicle on a level surface and check the engine oil level, started, stop it and allow 10 minutes before checking, check engine oil for white milky appearance excessive contamination, if engine oil becomes milky, it is highly probable that it is contaminated with engine coolant.
Check for engine oil leakage around following areas, intake valve timing control solenoid valve, mating surface between cylinder block cylinder head, mating surface between cylinder head rocker cover.
Crankshaft oil seals (front rear), oil filter (for intake valve timing control), remove oil pressure switch using suitable tool, do not drop or shock oil pressure switch.
Start engine and warm it up normal operating temperature, check oil pressure with engine running under no-load, when engine oil temperature is low, engine oil pressure becomes high, if difference is extreme, check oil passage and oil pump oil leaks.
After the inspections, install oil pressure switch follows, remove old liquid gasket adhering to oil pressure switch engine, apply liquid gasket and tighten oil pressure switch specification, use Genuine Silicone RTV Sealant or equivalent.
After warming up engine, make sure there are no leaks of engine oil with running engine, prolonged and repeated contact with used engine oil may cause skin cancer; try avoid direct skin, oil pan drain plug : 34.
Manual Description
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"12, precaution Necessary for Steering Wheel Rotation After Battery Disconnect12, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM).
Remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, if DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, maximum measuring range: 2,452 kPa (25, adapting oil pressure gauge oil pan (upper), removing and installing oil pressure switch.
Before starting engine, park vehicle on a level surface and check the engine oil level, started, stop it and allow 10 minutes before checking, check engine oil for white milky appearance excessive contamination, if engine oil becomes milky, it is highly probable that it is contaminated with engine coolant.
Check for engine oil leakage around following areas, intake valve timing control solenoid valve, mating surface between cylinder block cylinder head, mating surface between cylinder head rocker cover.
Crankshaft oil seals (front rear), oil filter (for intake valve timing control), remove oil pressure switch using suitable tool, do not drop or shock oil pressure switch.
Start engine and warm it up normal operating temperature, check oil pressure with engine running under no-load, when engine oil temperature is low, engine oil pressure becomes high, if difference is extreme, check oil passage and oil pump oil leaks.
After the inspections, install oil pressure switch follows, remove old liquid gasket adhering to oil pressure switch engine, apply liquid gasket and tighten oil pressure switch specification, use Genuine Silicone RTV Sealant or equivalent.
After warming up engine, make sure there are no leaks of engine oil with running engine, prolonged and repeated contact with used engine oil may cause skin cancer; try avoid direct skin, oil pan drain plug : 34.
Nissan Models