2010 Nissan Sentra - Accelerator Control System (Section ACC) (5 pages)
Download Accelerator Control System (Section ACC)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, do not disassemble accelerator pedal assembly, avoid impact from dropping etc.
Be careful to keep accelerator pedal assembly away water, disconnect accelerator pedal position sensor harness connector, remove the accelerator pedal assembly nuts and remove accelerator pedal assembly, installation is in the reverse order removal.
Check the accelerator pedal for smooth operation, be no binding or sticking when applying or releasing accelerator pedal, check that the accelerator pedal moves through full specified, distance of the specified pedal travel (A).
When the accelerator pedal position sensor harness connecLBIA0474E, tor is disconnected, perform Accelerator Pedal Released, released Position Learning" (MR20DE For California), EC-654, "Accelerator Pedal Released Position, learning" Except For California), EC-1193, "Accelerator Pedal Released Position Learning".
SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total travel (A)...
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, do not disassemble accelerator pedal assembly, avoid impact from dropping etc.
Be careful to keep accelerator pedal assembly away water, disconnect accelerator pedal position sensor harness connector, remove the accelerator pedal assembly nuts and remove accelerator pedal assembly, installation is in the reverse order removal.
Check the accelerator pedal for smooth operation, be no binding or sticking when applying or releasing accelerator pedal, check that the accelerator pedal moves through full specified, distance of the specified pedal travel (A).
When the accelerator pedal position sensor harness connecLBIA0474E, tor is disconnected, perform Accelerator Pedal Released, released Position Learning" (MR20DE For California), EC-654, "Accelerator Pedal Released Position, learning" Except For California), EC-1193, "Accelerator Pedal Released Position Learning".
SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total travel (A)...
Nissan Models