2014 Nissan Pathfinder - Seat (Section SE) (135 pages)
Download Seat (Section SE)
Manual Description
POWER SEAT FOR DRIVER SIDE WITHOUT, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, pOWER SEAT FOR PASSENGER SIDE 20, dIAGNOSIS AND REPAIR WORK FLOW 47.
CLIMATE CONTROLLED SEAT SYSTEM : Component Parts Location 10, cLIMATE CONTROLLED SEAT SYSTEM : Component Description 10, cLIMATE CONTROLLED SEAT SYSTEM : System Diagram 12, cLIMATE CONTROLLED SEAT SYSTEM : System Description 12.
POWER SUPPLY AND GROUND CIRCUIT 49, seat Cushion Thermal Electric Device 88, sEAT CUSHION THERMAL ELECTRIC DEVICE 60, rH Seat Track Tilt Release Cable 105.
SEAT CUSHION THERMAL ELECTRIC DEVICE SENSOR 62, cLIMATE CONTROLLED SEAT SWITCH INDICATOR 67, lH SEAT : Seat Cushion 128, sQUEAK AND RATTLE TROUBLE DIAGNOSES 71.
Generic Squeak Rattle Troubleshooting 72, rH SEAT : Seat Cushion 130, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least three minutes before performing any service, replace occupant classification system as part of the passenger front seat frame assembly, when removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it, protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip.
Be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly, follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area.
Then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty, then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, securing second row seat slides removal, replace any clips which are damaged during removal installation, cLIMATE CONTROLLED SEAT SYSTEM : Component Parts Location.
Climate controlled seat blower mo- 6, climate controlled seat relay (view with, cLIMATE CONTROLLED SEAT SYSTEM : Component Description, supplies power to the climate controlled seat control unit in accordance with key switch.
Installed in the seat cushion and controls the climate controlled seat blower motor, seatback thermal electric device, and seat cushion thermal electric device accordance with, installed in the center console and transmits signals to climate controlled seat control unit, in accordance with the HEAT (heated airflow) or COOL (cooled airflow) switch operation.
Manual Description
POWER SEAT FOR DRIVER SIDE WITHOUT, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, pOWER SEAT FOR PASSENGER SIDE 20, dIAGNOSIS AND REPAIR WORK FLOW 47.
CLIMATE CONTROLLED SEAT SYSTEM : Component Parts Location 10, cLIMATE CONTROLLED SEAT SYSTEM : Component Description 10, cLIMATE CONTROLLED SEAT SYSTEM : System Diagram 12, cLIMATE CONTROLLED SEAT SYSTEM : System Description 12.
POWER SUPPLY AND GROUND CIRCUIT 49, seat Cushion Thermal Electric Device 88, sEAT CUSHION THERMAL ELECTRIC DEVICE 60, rH Seat Track Tilt Release Cable 105.
SEAT CUSHION THERMAL ELECTRIC DEVICE SENSOR 62, cLIMATE CONTROLLED SEAT SWITCH INDICATOR 67, lH SEAT : Seat Cushion 128, sQUEAK AND RATTLE TROUBLE DIAGNOSES 71.
Generic Squeak Rattle Troubleshooting 72, rH SEAT : Seat Cushion 130, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.
Battery and wait at least three minutes before performing any service, replace occupant classification system as part of the passenger front seat frame assembly, when removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it, protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip.
Be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly, follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area.
Then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty, then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, securing second row seat slides removal, replace any clips which are damaged during removal installation, cLIMATE CONTROLLED SEAT SYSTEM : Component Parts Location.
Climate controlled seat blower mo- 6, climate controlled seat relay (view with, cLIMATE CONTROLLED SEAT SYSTEM : Component Description, supplies power to the climate controlled seat control unit in accordance with key switch.
Installed in the seat cushion and controls the climate controlled seat blower motor, seatback thermal electric device, and seat cushion thermal electric device accordance with, installed in the center console and transmits signals to climate controlled seat control unit, in accordance with the HEAT (heated airflow) or COOL (cooled airflow) switch operation.
Nissan Models