2014 Nissan Pathfinder - Heater & Air Condition (Section HA) (50 pages)
Download Heater & Air Condition (Section HA)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 4, precautions For Refrigerant System Service 4, oil Adjusting Procedure for Components Replacement Except Compressor25.
Oil Adjusting Procedure Compressor Replacement26, mAGNET CLUTCH : Removal Installation, trouble Diagnosis For Unusual Pressure 18, lOW-PRESSURE FLEXIBLE HOSE : Removal.
HIGH-PRESSURE PIPE : Removal Installation 35, lOW-PRESSURE A/C PIPES : Exploded View 36, lOW-PRESSURE A/C PIPES : Removal Installation 36, cONDENSER : Removal Installation 38.
CONDENSER PIPE ASSEMBLY : Removal, hEATING AND COOLING UNIT ASSEMBLY , removal and Installation - Front Heating, exploded View - Rear Cooling Unit Assembly 42.
Removal and Installation - Rear Cooling Unit Assembly 43, hEATER CORE : Exploded View 44, hEATER CORE : Removal Installation 44, eVAPORATOR : Removal Installation - Front.
EVAPORATOR : Removal Installation - Rear, eXPANSION VALVE : Exploded View 46, eXPANSION VALVE : Removal and Installation Front Expansion Valve 47, eXPANSION VALVE : Removal and Installation Rear Expansion Valve 47.
LIQUID TANK : Removal Installation 39, rEFRIGERANT PRESSURE SENSOR : Removal Installation 39, hEATING AND COOLING UNIT ASSEMBLY 41, exploded View - Front Heating Cooling Unit.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with Igni- H, tion ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect HA, battery and wait at least three minutes before performing any service.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner, precaution for Procedure without Cowl Top Cover.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 4, precautions For Refrigerant System Service 4, oil Adjusting Procedure for Components Replacement Except Compressor25.
Oil Adjusting Procedure Compressor Replacement26, mAGNET CLUTCH : Removal Installation, trouble Diagnosis For Unusual Pressure 18, lOW-PRESSURE FLEXIBLE HOSE : Removal.
HIGH-PRESSURE PIPE : Removal Installation 35, lOW-PRESSURE A/C PIPES : Exploded View 36, lOW-PRESSURE A/C PIPES : Removal Installation 36, cONDENSER : Removal Installation 38.
CONDENSER PIPE ASSEMBLY : Removal, hEATING AND COOLING UNIT ASSEMBLY , removal and Installation - Front Heating, exploded View - Rear Cooling Unit Assembly 42.
Removal and Installation - Rear Cooling Unit Assembly 43, hEATER CORE : Exploded View 44, hEATER CORE : Removal Installation 44, eVAPORATOR : Removal Installation - Front.
EVAPORATOR : Removal Installation - Rear, eXPANSION VALVE : Exploded View 46, eXPANSION VALVE : Removal and Installation Front Expansion Valve 47, eXPANSION VALVE : Removal and Installation Rear Expansion Valve 47.
LIQUID TANK : Removal Installation 39, rEFRIGERANT PRESSURE SENSOR : Removal Installation 39, hEATING AND COOLING UNIT ASSEMBLY 41, exploded View - Front Heating Cooling Unit.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with Igni- H, tion ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect HA, battery and wait at least three minutes before performing any service.
When removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it.
Protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly.
Follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner, precaution for Procedure without Cowl Top Cover.
Nissan Models