2011 Nissan Pathfinder - Parking Brake System (Section PB) (11 pages)
Download Parking Brake System (Section PB)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, measuring rear rotor drum inner diameter, when parking brake pedal is operated with the specified force, make sure the stroke within specified.
: Refer to PB-11, "Parking Brake Control", make sure the components are attached properly, checking looseness backlash, check parking brake pedal assembly for bends, damage and cracks, replace necessary, check cable for wear and damage, replace necessary.
Check parking brake warning lamp switch for malfunction, and replace if necessary, partially engage parking brake pedal access adjusting nut, insert a deep socket wrench to rotate adjusting nut loosen, cable until tension is sufficiently released.
Remove the rear wheel and tire using power tools, using wheel nuts, secure the disc to the hub to prevent it tilting, remove the adjuster hole plug installed on disc rotor, the adjuster in direction (A) using a suitable tool or flatbladed screw driver as shown, until disc rotor locked.
Adjuster in the opposite direction by 5 or 6 notches after locking, rotate disc rotor to make sure there no drag, if parking brake cable was replaced, operate parking brake, pedal or more times with a full stroke of 232.
Rotate the adjustment nut to adjust parking brake pedal operating force to 196 N-f (20, within the specified number notches, release the parking brake pedal and rotate the disc rotor to make sure there no drag, remove the instrument lower panel LH and center console.
(instrument panel) and IP-21, "Removal Installation" (center console), do not reuse adjusting nut after removing it, installation of Brake Caliper Disc Rotor", installation is in the reverse order removal.
Clean the brakes with a vacuum dust collector to minimize the hazard of airborne particles other, remove the disc rotor only with the parking brake pedal completely disengaged, check the thickness shoe lining.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, measuring rear rotor drum inner diameter, when parking brake pedal is operated with the specified force, make sure the stroke within specified.
: Refer to PB-11, "Parking Brake Control", make sure the components are attached properly, checking looseness backlash, check parking brake pedal assembly for bends, damage and cracks, replace necessary, check cable for wear and damage, replace necessary.
Check parking brake warning lamp switch for malfunction, and replace if necessary, partially engage parking brake pedal access adjusting nut, insert a deep socket wrench to rotate adjusting nut loosen, cable until tension is sufficiently released.
Remove the rear wheel and tire using power tools, using wheel nuts, secure the disc to the hub to prevent it tilting, remove the adjuster hole plug installed on disc rotor, the adjuster in direction (A) using a suitable tool or flatbladed screw driver as shown, until disc rotor locked.
Adjuster in the opposite direction by 5 or 6 notches after locking, rotate disc rotor to make sure there no drag, if parking brake cable was replaced, operate parking brake, pedal or more times with a full stroke of 232.
Rotate the adjustment nut to adjust parking brake pedal operating force to 196 N-f (20, within the specified number notches, release the parking brake pedal and rotate the disc rotor to make sure there no drag, remove the instrument lower panel LH and center console.
(instrument panel) and IP-21, "Removal Installation" (center console), do not reuse adjusting nut after removing it, installation of Brake Caliper Disc Rotor", installation is in the reverse order removal.
Clean the brakes with a vacuum dust collector to minimize the hazard of airborne particles other, remove the disc rotor only with the parking brake pedal completely disengaged, check the thickness shoe lining.
Nissan Models