2008 Nissan Pathfinder - Enging Cooling System (Section CO) (53 pages)
Download Enging Cooling System (Section CO)
Manual Description
WATER INLET AND THERMOSTAT ASSEMBLY 26, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"30, wATER OUTLET AND WATER PIPING 28.
Removal and Installation (Crankshaft driven type) 19, removal and Installation (Motor driven type) 20, removal and Installation (Motor Driven Type) 47, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, after removing nuts and bolts, separate the mating surface, using Tool and remove old liquid gasket sealing, be careful not to damage mating surfaces, tap Tool to insert it, and then slide it by tapping side.
In areas where Tool is difficult to use, use plastic hammer lightly, tap the parts, remove it, if for some unavoidable reason suitable tool such as screwdriver is used, be careful not to damage mating surfaces, remove the old liquid gasket adhering gasket application.
Surface and the mating surface using suitable tool, remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes, thoroughly clean the mating surfaces remove adhering.
Use Genuine RTV Silicone Sealant equivalent, apply the liquid gasket without breaks specified location, within five minutes of liquid gasket application, install mating component, if the liquid gasket protrudes, wipe it off immediately.
Do not retighten after installation, wait minutes or more after installation before refilling, engine with engine oil engine coolant, if there are specific instructions in manual, observe them.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removing chain tensioner cover water, pressing the tube liquid gasket, adapting radiator cap tester radiator cap.
Adapting radiator cap tester reservoir filler, adapting radiator cap tester reservoir cap, o-ring for damage, deterioration improper fitting, exhaust gas leaks into coolCylinder head gasket deteriing system.
Driving in low gear extended time, never remove the radiator/reservoir cap when the engine is hot, high pressure fluid escaping from radiator reservoir, wrap a thick cloth around the cap.
Check if the engine coolant reservoir tank level within MIN, adjust engine coolant level necessary, pressure coolant escaping from radiator reservoir, to check for leakage, apply pressure to cooling system using.
Higher pressure than specified may cause radiator damage, in case that engine coolant decreases, replenish cooling system with, if any concerns are found, repair replace damaged parts.
Manual Description
WATER INLET AND THERMOSTAT ASSEMBLY 26, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"30, wATER OUTLET AND WATER PIPING 28.
Removal and Installation (Crankshaft driven type) 19, removal and Installation (Motor driven type) 20, removal and Installation (Motor Driven Type) 47, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, after removing nuts and bolts, separate the mating surface, using Tool and remove old liquid gasket sealing, be careful not to damage mating surfaces, tap Tool to insert it, and then slide it by tapping side.
In areas where Tool is difficult to use, use plastic hammer lightly, tap the parts, remove it, if for some unavoidable reason suitable tool such as screwdriver is used, be careful not to damage mating surfaces, remove the old liquid gasket adhering gasket application.
Surface and the mating surface using suitable tool, remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes, thoroughly clean the mating surfaces remove adhering.
Use Genuine RTV Silicone Sealant equivalent, apply the liquid gasket without breaks specified location, within five minutes of liquid gasket application, install mating component, if the liquid gasket protrudes, wipe it off immediately.
Do not retighten after installation, wait minutes or more after installation before refilling, engine with engine oil engine coolant, if there are specific instructions in manual, observe them.
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removing chain tensioner cover water, pressing the tube liquid gasket, adapting radiator cap tester radiator cap.
Adapting radiator cap tester reservoir filler, adapting radiator cap tester reservoir cap, o-ring for damage, deterioration improper fitting, exhaust gas leaks into coolCylinder head gasket deteriing system.
Driving in low gear extended time, never remove the radiator/reservoir cap when the engine is hot, high pressure fluid escaping from radiator reservoir, wrap a thick cloth around the cap.
Check if the engine coolant reservoir tank level within MIN, adjust engine coolant level necessary, pressure coolant escaping from radiator reservoir, to check for leakage, apply pressure to cooling system using.
Higher pressure than specified may cause radiator damage, in case that engine coolant decreases, replenish cooling system with, if any concerns are found, repair replace damaged parts.
Nissan Models