2013 Nissan Murano - Steering System (Section ST) (107 pages)
Download Steering System (Section ST)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 4, service Notice or Precautions Steering System, hEATED STEERING WHEEL SWITCH INDICATOR LAMP 18, component Description (Heated Steering Wheel) 8.
HEATED STEERING WHEEL SWITCH INDICATOR LAMP DOES NOT TURN ON 24, system Description (Heated Steering Wheel) 9, wITHOUT ELECTRIC MOTOR : Exploded View 35, wITHOUT ELECTRIC MOTOR : Removal Installation 35.
WITHOUT ELECTRIC MOTOR : Inspection 36, wITH ELECTRIC MOTOR : Exploded View 38, wITH ELECTRIC MOTOR : Removal Installation 38, wITH ELECTRIC MOTOR : Inspection 39.
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, steering Wheel Axial End Play Play 65, socket Swing Force Rotating Torque 66, steering Wheel Axial End Play Play 106.
Socket Swing Force Rotating Torque 107, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, in case of removing steering gear assembly, make the final tightening with grounded unloaded vehicle, condition, and then check wheel alignment.
Observe the following precautions when disassembling, - Before disassembly, thoroughly clean the outside unit, - Disassembly should be done in a clean work area, contaminated by dirt other foreign matter.
- For easier and proper assembly, place disassembled parts in order parts rack, - Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with, - Before assembling, apply the specified grease directed parts, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Measuring steering column rotating torque, measuring ball joint rotating torque, component Parts Location (Heated Steering Wheel), refer to "Heated Steering Wheel".
Refer to "Heated Steering Wheel Relay", refer to "Heated Steering Wheel Switch", the heated steering wheel is activated by the power supply from the heated steering wheel relay, furthermore, the heated steering wheel incorporates a heating element and a thermostat control heated.
Heating element: Heat is generated by the passage an electric current, thermostat: ON/OFF operation of power supply certain temperature, controls the heated steering wheel relay and operates the heated steering wheel system.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 4, service Notice or Precautions Steering System, hEATED STEERING WHEEL SWITCH INDICATOR LAMP 18, component Description (Heated Steering Wheel) 8.
HEATED STEERING WHEEL SWITCH INDICATOR LAMP DOES NOT TURN ON 24, system Description (Heated Steering Wheel) 9, wITHOUT ELECTRIC MOTOR : Exploded View 35, wITHOUT ELECTRIC MOTOR : Removal Installation 35.
WITHOUT ELECTRIC MOTOR : Inspection 36, wITH ELECTRIC MOTOR : Exploded View 38, wITH ELECTRIC MOTOR : Removal Installation 38, wITH ELECTRIC MOTOR : Inspection 39.
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, steering Wheel Axial End Play Play 65, socket Swing Force Rotating Torque 66, steering Wheel Axial End Play Play 106.
Socket Swing Force Rotating Torque 107, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, in case of removing steering gear assembly, make the final tightening with grounded unloaded vehicle, condition, and then check wheel alignment.
Observe the following precautions when disassembling, - Before disassembly, thoroughly clean the outside unit, - Disassembly should be done in a clean work area, contaminated by dirt other foreign matter.
- For easier and proper assembly, place disassembled parts in order parts rack, - Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with, - Before assembling, apply the specified grease directed parts, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Measuring steering column rotating torque, measuring ball joint rotating torque, component Parts Location (Heated Steering Wheel), refer to "Heated Steering Wheel".
Refer to "Heated Steering Wheel Relay", refer to "Heated Steering Wheel Switch", the heated steering wheel is activated by the power supply from the heated steering wheel relay, furthermore, the heated steering wheel incorporates a heating element and a thermostat control heated.
Heating element: Heat is generated by the passage an electric current, thermostat: ON/OFF operation of power supply certain temperature, controls the heated steering wheel relay and operates the heated steering wheel system.
Nissan Models