2009 Nissan Murano - Engine Mechanical (Section EM) (151 pages)
Download Engine Mechanical (Section EM)
Manual Description
NVH Troubleshooting - Engine Noise 3, use the Chart Below to Help You Find Cause, precaution for Procedure without Cowl Top Cover 5, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 5.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect 5, precaution for Drain Engine Coolant Engine, precaution for Disconnecting Fuel Piping 6, precaution for Removal Disassembly 6.
Precaution for Inspection, Repair Replacement 6, precaution for Assembly Installation 6, aIR CLEANER AND AIR DUCT 27, dRIVE BELT AUTO TENSIONER AND IDLER.
FUEL INJECTOR AND FUEL TUBE 45, iGNITION COIL, SPARK PLUG AND ROCKER COVER 50, vALVE OIL SEAL : Removal Installation 103, fRONT OIL SEAL : Removal Installation 103.
REAR OIL SEAL : Removal Installation 104, aWD : Removal Installation 78, hOW TO SELECT PISTON AND BEARING 136, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Use the Chart Below to Help You Find the Cause Symptom, locate the area where noise occurs, specify the operating condition engine, if necessary, repair replace these parts.
B: Related C: Sometimes related —: Not related, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIRBAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch, oN or engine is running, never use air or electric power tools or strike near the sensor(s) with hammer, heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury, when using air or electric power tools or hammers, always turn OFF ignition switch, disconnect battery.
And wait minutes or more before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure.
Below before starting repair operation, supply power using jumper cables battery discharged, (At this time, the steering lock will be released.
Manual Description
NVH Troubleshooting - Engine Noise 3, use the Chart Below to Help You Find Cause, precaution for Procedure without Cowl Top Cover 5, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 5.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect 5, precaution for Drain Engine Coolant Engine, precaution for Disconnecting Fuel Piping 6, precaution for Removal Disassembly 6.
Precaution for Inspection, Repair Replacement 6, precaution for Assembly Installation 6, aIR CLEANER AND AIR DUCT 27, dRIVE BELT AUTO TENSIONER AND IDLER.
FUEL INJECTOR AND FUEL TUBE 45, iGNITION COIL, SPARK PLUG AND ROCKER COVER 50, vALVE OIL SEAL : Removal Installation 103, fRONT OIL SEAL : Removal Installation 103.
REAR OIL SEAL : Removal Installation 104, aWD : Removal Installation 78, hOW TO SELECT PISTON AND BEARING 136, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Use the Chart Below to Help You Find the Cause Symptom, locate the area where noise occurs, specify the operating condition engine, if necessary, repair replace these parts.
B: Related C: Sometimes related —: Not related, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIRBAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch, oN or engine is running, never use air or electric power tools or strike near the sensor(s) with hammer, heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury, when using air or electric power tools or hammers, always turn OFF ignition switch, disconnect battery.
And wait minutes or more before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure.
Below before starting repair operation, supply power using jumper cables battery discharged, (At this time, the steering lock will be released.
Nissan Models