2007 Nissan Murano - Road Wheels & Tires (Section WT) (56 pages)
Download Road Wheels & Tires (Section WT)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, lOW TIRE PRESSURE WARNING LAMP 9, tIRE PRESSURE WARNING CHECK SWITCH 9, wiring Diagram — T/WARN — 15.
BCM Input/Output Signal Reference Values 18, bCM INSPECTION TABLE (FOR LOW TIRE, trouble Diagnosis Chart Symptoms 28, low Tire Pressure Warning Lamp Symptom Chart 29.
DTC C1710, C1711 [NO DATA] 32, bCM TERMINALS AND REFERENCE VALUE 32, bCM TERMINALS AND REFERENCE VALUE 35, dTC C1722, C1723 [CODE ERR] 39.
CONSULT-II REFERENCE VALUE IN DATA, bCM TERMINALS AND REFERENCE VALUE 39, dTC C1726, C1727 [BATT VOLT, bCM TERMINALS AND REFERENCE VALUE 42.
DTC VHCL SPEED SIG ERR 45, low Tire Pressure Warning Lamp Does Not Turn, low Tire Pressure Warning Lamp Stays ON When, ignition Switch Is Turned ON 46.
Low Tire Pressure warning Lamp Blinks When Ignition Switch Is Turned ON 49, turn Signal Lamp Blinks When Ignition Switch Is, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, before connecting or disconnecting the BCM harness connector, turn ignition switch OFF” and disconnect the battery cable from the negative terminal.
Applied to BCM even if ignition switch turned OFF”, when connecting or disconnecting pin connectors into, from BCM, take care not to damage pin terminals (bend, when connecting pin connectors make sure that there.
Not any bends or breaks BCM pin terminals, before replacing BCM, perform control unit input/output, signal inspection and make sure whether BCM functions, low tire pressure warning lamp flashes 1min, then turns ON when occurring any malfunction except low.
ID registration is required when replacing or rotating wheels, replacing transmitter or BCM, replace grommet seal, valve core and cap of the transmitter in TPMS every tire replacement by reaching, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Refer to ROAD WHEEL chart, use the chart below to help you find the cause of the symptom, during driving, the tire pressure monitoring system receives the signal transmitted transmitter, installed in each wheel, when the tire pressure becomes low.
When the tire pressure monitoring system detects low inflation pressure or another unusual symptom, warning lamps in the combination meter comes on, of the tire pressure warning check connector, a sensor-transmitter integrated with a valve installed.
Wheel and transmits a detected air pressure signal form, the remote keyless entry receiver (1) receives the air pressure signal transmitted by the transmitter each wheel, key-less entry receiver, and controls the low tire pressure warning.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, lOW TIRE PRESSURE WARNING LAMP 9, tIRE PRESSURE WARNING CHECK SWITCH 9, wiring Diagram — T/WARN — 15.
BCM Input/Output Signal Reference Values 18, bCM INSPECTION TABLE (FOR LOW TIRE, trouble Diagnosis Chart Symptoms 28, low Tire Pressure Warning Lamp Symptom Chart 29.
DTC C1710, C1711 [NO DATA] 32, bCM TERMINALS AND REFERENCE VALUE 32, bCM TERMINALS AND REFERENCE VALUE 35, dTC C1722, C1723 [CODE ERR] 39.
CONSULT-II REFERENCE VALUE IN DATA, bCM TERMINALS AND REFERENCE VALUE 39, dTC C1726, C1727 [BATT VOLT, bCM TERMINALS AND REFERENCE VALUE 42.
DTC VHCL SPEED SIG ERR 45, low Tire Pressure Warning Lamp Does Not Turn, low Tire Pressure Warning Lamp Stays ON When, ignition Switch Is Turned ON 46.
Low Tire Pressure warning Lamp Blinks When Ignition Switch Is Turned ON 49, turn Signal Lamp Blinks When Ignition Switch Is, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, before connecting or disconnecting the BCM harness connector, turn ignition switch OFF” and disconnect the battery cable from the negative terminal.
Applied to BCM even if ignition switch turned OFF”, when connecting or disconnecting pin connectors into, from BCM, take care not to damage pin terminals (bend, when connecting pin connectors make sure that there.
Not any bends or breaks BCM pin terminals, before replacing BCM, perform control unit input/output, signal inspection and make sure whether BCM functions, low tire pressure warning lamp flashes 1min, then turns ON when occurring any malfunction except low.
ID registration is required when replacing or rotating wheels, replacing transmitter or BCM, replace grommet seal, valve core and cap of the transmitter in TPMS every tire replacement by reaching, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Refer to ROAD WHEEL chart, use the chart below to help you find the cause of the symptom, during driving, the tire pressure monitoring system receives the signal transmitted transmitter, installed in each wheel, when the tire pressure becomes low.
When the tire pressure monitoring system detects low inflation pressure or another unusual symptom, warning lamps in the combination meter comes on, of the tire pressure warning check connector, a sensor-transmitter integrated with a valve installed.
Wheel and transmits a detected air pressure signal form, the remote keyless entry receiver (1) receives the air pressure signal transmitted by the transmitter each wheel, key-less entry receiver, and controls the low tire pressure warning.
Nissan Models