2009 Nissan Maxima - Engine Mechanical (Section EM) (132 pages)
Download Engine Mechanical (Section EM)
Manual Description
Removal and Installation Drive Belt Auto-tensioner15, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions Necessary for Steering Wheel Rotation after Battery Disconnect 3, precaution for Disconnecting Fuel Piping 4.
Precaution for Removal Disassembly 4, precaution for Inspection, Repair Replacement 4, precaution for Assembly Installation 4, aIR CLEANER AND AIR DUCT 23.
NVH Troubleshooting - Engine Noise 10, use the Chart Below to Help You Find Cause, fUEL INJECTOR AND FUEL TUBE 40, removal and Installation of Valve Oil Seal 81.
Removal and Installation of Front Oil Seal 81, removal and Installation of Rear Oil Seal 83, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Precautions Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
This vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation.
Supply power using jumper cables battery discharged, carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables.
The push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III, drain coolant when engine cooled.
Before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disassembly, after disconnecting pipes, plug openings stop fuel leakage, when instructed to use special service tools, use the specified tools.
Exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or the equivalent, if necessary, to seal out foreign materials, mark and arrange disassembly parts in an organized way for easy troubleshooting assembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally.
Precaution for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part.
Manual Description
Removal and Installation Drive Belt Auto-tensioner15, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions Necessary for Steering Wheel Rotation after Battery Disconnect 3, precaution for Disconnecting Fuel Piping 4.
Precaution for Removal Disassembly 4, precaution for Inspection, Repair Replacement 4, precaution for Assembly Installation 4, aIR CLEANER AND AIR DUCT 23.
NVH Troubleshooting - Engine Noise 10, use the Chart Below to Help You Find Cause, fUEL INJECTOR AND FUEL TUBE 40, removal and Installation of Valve Oil Seal 81.
Removal and Installation of Front Oil Seal 81, removal and Installation of Rear Oil Seal 83, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
Precautions Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
This vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation.
Supply power using jumper cables battery discharged, carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables.
The push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III, drain coolant when engine cooled.
Before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disassembly, after disconnecting pipes, plug openings stop fuel leakage, when instructed to use special service tools, use the specified tools.
Exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or the equivalent, if necessary, to seal out foreign materials, mark and arrange disassembly parts in an organized way for easy troubleshooting assembly, when loosening nuts and bolts, as a basic rule, start with the one furthest outside, then one diagonally.
Precaution for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts, use torque wrench to tighten bolts nuts specification, when tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with.
Ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, thoroughly wash, clean, and air-blow each part.
Nissan Models