2006 Nissan Maxima - Brake System (Section BR) (38 pages)
Download Brake System (Section BR)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, front Brake Piping Hose 9, rear Brake Piping Hose 10, removal and Installation Brake Pad 24.
Removal and Installation Caliper Assembly, disassembly and Assembly Caliper Assembly 26, removal and Installation Brake Pad 30, disassembly and Assembly Caliper Assembly 31.
Precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along B, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Formed by an authorized NISSAN/INFINITI dealer, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, be careful not to splash brake fluid on painted areas; it may.
Was it away with water immediately, to clean or wash all parts of master cylinder, disc brake caliper, and wheel cylinder, use clean brake fluid, never use mineral oils such as gasoline kerosene.
Ruin rubber parts hydraulic system, use flare nut wrench when removing installing brake tube, always tighten brake lines to specified torque when installing, burnish the brake contact surfaces after refinishing or replacing drums or rotors, after replacing pads.
Linings, or if a soft pedal occurs at very low mileage, clean brake pads and shoes with a waste cloth, then wipe with dust collector, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, brake and clutch pedal height measurement tool.
Removing and installing each brake piping, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, "NVH Troubleshooting Chart", RSU-4, "NVH Troubleshooting Chart", "NVH Troubleshooting Chart", RAX-4, "NVH Troubleshooting Chart".
Use the chart below to help you find the cause of the symptom, inspect the brake pedal free height "H" dash reinforcement, stop lamp switch ASCD switch (J), threaded end of stop lamp switch ASCD.
Pedal height (with engine running, brake, pedal force N {50 kg-f, 110 lb-f}) "H", : More than 84 mm (3, loosen the stop lamp switch and ASCD switch by turning 45°.
Loosen lock nut on the input rod, then turn input rod adjust, make sure that the screw portion of the end input rod, with the pedal pulled up and held by hand, press stop lamp, switch and the ASCD switch in until ends contact rubber stops.
With the ends of the stop lamp switch and ASCD switch contacting the rubber stops, turn switches 45°, make sure that the gap (I 1, I2) between the rubber stops and switch ends within specification, make sure that the stop lamp goes off when pedal released, start the engine and check the height of the brake pedal when depressing it.
Do not deform brake tube, check brake pedal following items, crack or deformation clevis pin stopper, installation is in the reverse order removal.
After installing the brake pedal assembly in the vehicle, be sure to adjust it, check fluid level in reservoir tank, visually check around the reservoir tank leaks.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, front Brake Piping Hose 9, rear Brake Piping Hose 10, removal and Installation Brake Pad 24.
Removal and Installation Caliper Assembly, disassembly and Assembly Caliper Assembly 26, removal and Installation Brake Pad 30, disassembly and Assembly Caliper Assembly 31.
Precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along B, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Formed by an authorized NISSAN/INFINITI dealer, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, be careful not to splash brake fluid on painted areas; it may.
Was it away with water immediately, to clean or wash all parts of master cylinder, disc brake caliper, and wheel cylinder, use clean brake fluid, never use mineral oils such as gasoline kerosene.
Ruin rubber parts hydraulic system, use flare nut wrench when removing installing brake tube, always tighten brake lines to specified torque when installing, burnish the brake contact surfaces after refinishing or replacing drums or rotors, after replacing pads.
Linings, or if a soft pedal occurs at very low mileage, clean brake pads and shoes with a waste cloth, then wipe with dust collector, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, brake and clutch pedal height measurement tool.
Removing and installing each brake piping, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, "NVH Troubleshooting Chart", RSU-4, "NVH Troubleshooting Chart", "NVH Troubleshooting Chart", RAX-4, "NVH Troubleshooting Chart".
Use the chart below to help you find the cause of the symptom, inspect the brake pedal free height "H" dash reinforcement, stop lamp switch ASCD switch (J), threaded end of stop lamp switch ASCD.
Pedal height (with engine running, brake, pedal force N {50 kg-f, 110 lb-f}) "H", : More than 84 mm (3, loosen the stop lamp switch and ASCD switch by turning 45°.
Loosen lock nut on the input rod, then turn input rod adjust, make sure that the screw portion of the end input rod, with the pedal pulled up and held by hand, press stop lamp, switch and the ASCD switch in until ends contact rubber stops.
With the ends of the stop lamp switch and ASCD switch contacting the rubber stops, turn switches 45°, make sure that the gap (I 1, I2) between the rubber stops and switch ends within specification, make sure that the stop lamp goes off when pedal released, start the engine and check the height of the brake pedal when depressing it.
Do not deform brake tube, check brake pedal following items, crack or deformation clevis pin stopper, installation is in the reverse order removal.
After installing the brake pedal assembly in the vehicle, be sure to adjust it, check fluid level in reservoir tank, visually check around the reservoir tank leaks.
Nissan Models