2001 Nissan Maxima - Automatic Transmission (Section AT) (392 pages)
Download Automatic Transmission (Section AT)
Manual Description
Precautions for On Board Diagnostic (OBD), one or Two Trip Detection Logic OBD-II36, wiring Diagram — AT — MAIN99, wiring Diagram — AT — PNP/SW104.
DTC A/T FLUID TEMPERATURE SENSOR, wiring Diagram — AT — FTS110, wiring Diagram — AT — VSSA/T116, wiring Diagram — AT — ENGSS121.
DTC A/T 1ST GEAR FUNCTION124, wiring Diagram — AT — 1ST127, dTC A/T 2ND GEAR FUNCTION130, wiring Diagram — AT — 2ND133.
DTC A/T 3RD GEAR FUNCTION136, wiring Diagram — AT — 3RD139, dTC A/T 4TH GEAR FUNCTION142, wiring Diagram — AT — 4TH146.
Wiring Diagram — AT — TCV153, wiring Diagram — AT — TCCSIG159, dTC LINE PRESSURE SOLENOID VALVE166, wiring Diagram — AT — LPSV168.
DTC SHIFT SOLENOID VALVE A172, wiring Diagram — AT — SSV/A174, dTC SHIFT SOLENOID VALVE B177, wiring Diagram — AT — SSV/B179.
Wiring Diagram — AT — TPS185, wiring Diagram — AT — OVRCSV193, dTC BATT/FLUID TEMP SEN (A/T FLUID TEMP, sENSOR CIRCUIT AND TCM POWER SOURCE)196.
Wiring Diagram — AT — BA/FTS198, wiring Diagram — AT — VSSMTR205, wiring Diagram — AT — LAN210, dTC CONTROL UNIT (RAM), CONTROL UNIT.
Wiring Diagram — AT — NONDTC216, overdrive Control Switch ON -> OFF257, overdrive Control Throttle Position Switches, shift Lock System Electrical Parts Location272.
Locations of Adjusting Shims, Needle Bearings, rear Internal Gear, Forward Clutch Hub, output Shaft, Idler Gear, Reduction Pinion Gear, these numbers are prescribed by SAE J2012.
When the fail-safe operation occurs, MIL illuminates, the MIL illuminates when both the Revolution sensor signal” and the Vehicle speed sensor signal” meet fail-safe condition, supplemental Restraint System (SRS) AIR BAG” SEAT BELT PRE-TENSIONER”, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER” used along with.
A seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain types, the Supplemental Restraint System consists of driver air bag module (located in the center of the steering wheel), front passenger air bag module (located on the instrument panel on passenger side), seat belt, pre-tensioners, a diagnosis sensor unit, crash zone sensor, warning lamp, wiring harness spiral cable, the Supplemental Restraint System consists of front side air bag module (located in the outer side front.
Seat), satellite sensor, diagnosis sensor unit (one of components of air bags for frontal collision), wiring, harness, warning lamp (one of components of air bags frontal collision), information necessary to service the system safely is included in the RS section Service Manual, ¼ To avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
¼ Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, driver of a malfunction causing emission deterioration, ¼ Be sure to turn the ignition switch OFF and disconnect the negative battery terminal before any.
Manual Description
Precautions for On Board Diagnostic (OBD), one or Two Trip Detection Logic OBD-II36, wiring Diagram — AT — MAIN99, wiring Diagram — AT — PNP/SW104.
DTC A/T FLUID TEMPERATURE SENSOR, wiring Diagram — AT — FTS110, wiring Diagram — AT — VSSA/T116, wiring Diagram — AT — ENGSS121.
DTC A/T 1ST GEAR FUNCTION124, wiring Diagram — AT — 1ST127, dTC A/T 2ND GEAR FUNCTION130, wiring Diagram — AT — 2ND133.
DTC A/T 3RD GEAR FUNCTION136, wiring Diagram — AT — 3RD139, dTC A/T 4TH GEAR FUNCTION142, wiring Diagram — AT — 4TH146.
Wiring Diagram — AT — TCV153, wiring Diagram — AT — TCCSIG159, dTC LINE PRESSURE SOLENOID VALVE166, wiring Diagram — AT — LPSV168.
DTC SHIFT SOLENOID VALVE A172, wiring Diagram — AT — SSV/A174, dTC SHIFT SOLENOID VALVE B177, wiring Diagram — AT — SSV/B179.
Wiring Diagram — AT — TPS185, wiring Diagram — AT — OVRCSV193, dTC BATT/FLUID TEMP SEN (A/T FLUID TEMP, sENSOR CIRCUIT AND TCM POWER SOURCE)196.
Wiring Diagram — AT — BA/FTS198, wiring Diagram — AT — VSSMTR205, wiring Diagram — AT — LAN210, dTC CONTROL UNIT (RAM), CONTROL UNIT.
Wiring Diagram — AT — NONDTC216, overdrive Control Switch ON -> OFF257, overdrive Control Throttle Position Switches, shift Lock System Electrical Parts Location272.
Locations of Adjusting Shims, Needle Bearings, rear Internal Gear, Forward Clutch Hub, output Shaft, Idler Gear, Reduction Pinion Gear, these numbers are prescribed by SAE J2012.
When the fail-safe operation occurs, MIL illuminates, the MIL illuminates when both the Revolution sensor signal” and the Vehicle speed sensor signal” meet fail-safe condition, supplemental Restraint System (SRS) AIR BAG” SEAT BELT PRE-TENSIONER”, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER” used along with.
A seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain types, the Supplemental Restraint System consists of driver air bag module (located in the center of the steering wheel), front passenger air bag module (located on the instrument panel on passenger side), seat belt, pre-tensioners, a diagnosis sensor unit, crash zone sensor, warning lamp, wiring harness spiral cable, the Supplemental Restraint System consists of front side air bag module (located in the outer side front.
Seat), satellite sensor, diagnosis sensor unit (one of components of air bags for frontal collision), wiring, harness, warning lamp (one of components of air bags frontal collision), information necessary to service the system safely is included in the RS section Service Manual, ¼ To avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
¼ Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, driver of a malfunction causing emission deterioration, ¼ Be sure to turn the ignition switch OFF and disconnect the negative battery terminal before any.
Nissan Models