2012 Nissan Leaf - General Information (Section GI) (63 pages)
Download General Information (Section GI)
Manual Description
HOW TO USE THIS MANUAL 3, relation between Illustrations Descriptions 4, precaution for Technicians Using Medical Electric 25, point to Be Checked Before Starting Maintenance.
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"25, precautions Necessary for Steering Wheel Rotation After Battery Disconnection26, precaution for Procedure without Cowl Top Cover 27, hOW TO FOLLOW TROUBLE DIAGNOSES 6.
How to Follow Test Groups Trouble Diagnosis 6, key to Symbols Signifying Measurements Procedures 7, hOW TO READ WIRING DIAGRAMS 9, cAUTIONS AS TO HIGH VOLTAGE 31.
Insulated Protective Wear Insulating Tools35, handling of a Vehicle with Dead Battery40, tightening Torque Table (New Standard Included) 19, garage Jack and Safety Stand 2-Pole Lift41.
Recommended Chemical Products Sealants 21, vehicle Recovery (Freeing Stuck Vehicle)43, information About Identification Model Code 22, pROCEDURE FOR PARK LOCK RELEASE 45.
Control Units Electrical Parts 47, cONSULT Function System Application*1 59, cONSULT/GST Data Link Connector (DLC) Circuit 60, aDDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL 63.
This volume explains Removal, Disassembly, Installation, Inspection and Adjustment” Trouble Diagnoses”, to be used to inform an operation which will cause a death or serious personal injury instructions, example: Touching high voltage components without using appropriate protective equipment, to be used to inform an operation which may cause a death or serious personal injury instructions.
To be used to inform an operation which may cause personal injury or component damage if instructions not following, to be used to inform you helpful information, standard value: Tolerance inspection adjustment, dANGER, WARNING and NOTE Limit value: The maximum or minimum limit value that should not be exceeded inspection.
It may cause an electric shock if instructions are not following to be used in caution an operation, to be used to describe the removal of component, connector, etc, always wear when inspecting or performing service operation high voltage components, always wear when inspecting or performing service operation of high voltage components lift-up.
Always wear during under circumstances, during removal/installation or check operation of high voltage terminals harnessed where, spark might terminal appear by short circuit, always use when performing high voltage presents operation such as operation inside high voltage.
The UNITS given in this manual are primarily expressed as the SI UNIT (International System Unit), alternatively expressed in the metric system and yard/pound system, also with regard to tightening torque of bolts and nuts, there are descriptions both about range about, a QUICK REFERENCE INDEX, black tab (e.
First page of each section by matching it to section's black tab, tHE CONTENTS are listed on the first page each section, tHE TITLE is indicated on the upper portion of each page and shows part system, tHE PAGE NUMBER of each section consists of two or three letters which designate particular section.
THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks, work and hidden or tricky steps which are not shown in previous large illustrations, assembly, inspection and adjustment procedures for the complicated units such automatic transaxle, the following sample explains the relationship between the part description in an illustration, part name.
THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques, lubrication points, section number of the PARTS CATALOG (e, the illustrations should be used in reference to service matters only, components shown in an illustration may be identified by a circled number.
Manual Description
HOW TO USE THIS MANUAL 3, relation between Illustrations Descriptions 4, precaution for Technicians Using Medical Electric 25, point to Be Checked Before Starting Maintenance.
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"25, precautions Necessary for Steering Wheel Rotation After Battery Disconnection26, precaution for Procedure without Cowl Top Cover 27, hOW TO FOLLOW TROUBLE DIAGNOSES 6.
How to Follow Test Groups Trouble Diagnosis 6, key to Symbols Signifying Measurements Procedures 7, hOW TO READ WIRING DIAGRAMS 9, cAUTIONS AS TO HIGH VOLTAGE 31.
Insulated Protective Wear Insulating Tools35, handling of a Vehicle with Dead Battery40, tightening Torque Table (New Standard Included) 19, garage Jack and Safety Stand 2-Pole Lift41.
Recommended Chemical Products Sealants 21, vehicle Recovery (Freeing Stuck Vehicle)43, information About Identification Model Code 22, pROCEDURE FOR PARK LOCK RELEASE 45.
Control Units Electrical Parts 47, cONSULT Function System Application*1 59, cONSULT/GST Data Link Connector (DLC) Circuit 60, aDDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL 63.
This volume explains Removal, Disassembly, Installation, Inspection and Adjustment” Trouble Diagnoses”, to be used to inform an operation which will cause a death or serious personal injury instructions, example: Touching high voltage components without using appropriate protective equipment, to be used to inform an operation which may cause a death or serious personal injury instructions.
To be used to inform an operation which may cause personal injury or component damage if instructions not following, to be used to inform you helpful information, standard value: Tolerance inspection adjustment, dANGER, WARNING and NOTE Limit value: The maximum or minimum limit value that should not be exceeded inspection.
It may cause an electric shock if instructions are not following to be used in caution an operation, to be used to describe the removal of component, connector, etc, always wear when inspecting or performing service operation high voltage components, always wear when inspecting or performing service operation of high voltage components lift-up.
Always wear during under circumstances, during removal/installation or check operation of high voltage terminals harnessed where, spark might terminal appear by short circuit, always use when performing high voltage presents operation such as operation inside high voltage.
The UNITS given in this manual are primarily expressed as the SI UNIT (International System Unit), alternatively expressed in the metric system and yard/pound system, also with regard to tightening torque of bolts and nuts, there are descriptions both about range about, a QUICK REFERENCE INDEX, black tab (e.
First page of each section by matching it to section's black tab, tHE CONTENTS are listed on the first page each section, tHE TITLE is indicated on the upper portion of each page and shows part system, tHE PAGE NUMBER of each section consists of two or three letters which designate particular section.
THE SMALL ILLUSTRATIONS show the important steps such as inspection, use of special tools, knacks, work and hidden or tricky steps which are not shown in previous large illustrations, assembly, inspection and adjustment procedures for the complicated units such automatic transaxle, the following sample explains the relationship between the part description in an illustration, part name.
THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques, lubrication points, section number of the PARTS CATALOG (e, the illustrations should be used in reference to service matters only, components shown in an illustration may be identified by a circled number.
Nissan Models