2014 Nissan Juke - Power Supply, Ground & Circuit Elements (Section PG) (101 pages)
Download Power Supply, Ground & Circuit Elements (Section PG)
Manual Description
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS, wiring Diagram - IGNITION POWER SUPPLY, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3.
FUSE BLOCK - JUNCTION BOX (J/B) 62, fUSE, FUSIBLE LINK AND RELAY BOX 63, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 64, rEGULAR GRADE : Engine Room Harness66.
REGULAR GRADE : Engine Control Harness68, rEGULAR GRADE : Room Lamp Harness77, wiring Diagram - BATTERY POWER SUPPLY - 11, wiring Diagram - BATTERY POWER SUPPLY.
Wiring Diagram - ACCESSORY POWER SUPPLY - 34, wiring Diagram - ACCESSORY POWER SUPPLY FUSE No, wiring Diagram - IGNITION POWER SUPPLY - 41, bATTERY TERMINAL WITH FUSIBLE LINK 100.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition.
Switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals.
Main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, multitasking battery electrical diagnostic station.
Tests batteries, starting and charging systems charges batteries, for operating instructions, refer diagnostic, the PTC thermistor generates heat in response current flow, temperature (and resistance) of the thermistor element varies with.
Electrical resistance will rise sharply to control circuit current, reduced current flow will cause the element cool, accordingly and normal circuit current flow allowed resume, cold cranking current (For reference value).
HR*: Because of the frequent battery charge/discharge performed according to a driving condition and a battery condition, this model uses a charge/discharge capacity-enhanced battery, to use a genuine battery when replacement needed, the tab-locking type connectors help prevent accidental looseness disconnection, the tab-locking type connectors are disconnected by pushing or lifting the locking tab(s).
Never pull the harness or wires when disconnecting connector, a new style slide-locking type connector is used on certain systems components, especially those, the slide-locking type connectors help prevent incomplete locking and accidental looseness disconnection.
Manual Description
POWER SUPPLY, GROUND & CIRCUIT ELEMENTS, wiring Diagram - IGNITION POWER SUPPLY, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3.
FUSE BLOCK - JUNCTION BOX (J/B) 62, fUSE, FUSIBLE LINK AND RELAY BOX 63, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 64, rEGULAR GRADE : Engine Room Harness66.
REGULAR GRADE : Engine Control Harness68, rEGULAR GRADE : Room Lamp Harness77, wiring Diagram - BATTERY POWER SUPPLY - 11, wiring Diagram - BATTERY POWER SUPPLY.
Wiring Diagram - ACCESSORY POWER SUPPLY - 34, wiring Diagram - ACCESSORY POWER SUPPLY FUSE No, wiring Diagram - IGNITION POWER SUPPLY - 41, bATTERY TERMINAL WITH FUSIBLE LINK 100.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, precautions for Removing Battery Terminal, when removing the 12V battery terminal, turn OFF ignition.
Switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals.
Main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error, multitasking battery electrical diagnostic station.
Tests batteries, starting and charging systems charges batteries, for operating instructions, refer diagnostic, the PTC thermistor generates heat in response current flow, temperature (and resistance) of the thermistor element varies with.
Electrical resistance will rise sharply to control circuit current, reduced current flow will cause the element cool, accordingly and normal circuit current flow allowed resume, cold cranking current (For reference value).
HR*: Because of the frequent battery charge/discharge performed according to a driving condition and a battery condition, this model uses a charge/discharge capacity-enhanced battery, to use a genuine battery when replacement needed, the tab-locking type connectors help prevent accidental looseness disconnection, the tab-locking type connectors are disconnected by pushing or lifting the locking tab(s).
Never pull the harness or wires when disconnecting connector, a new style slide-locking type connector is used on certain systems components, especially those, the slide-locking type connectors help prevent incomplete locking and accidental looseness disconnection.
Nissan Models