2014 Nissan Juke - Meter, Warning Lamp & Indicator (Section MWI) (62 pages)
Download Meter, Warning Lamp & Indicator (Section MWI)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3, mETER SYSTEM : Component Parts Location 5, mETER SYSTEM : Component Description 6.
METER SYSTEM : System Diagram 7, mETER SYSTEM : System Description 7, oIL PRESSURE WARNING LAMP : System Description12, mETER ILLUMINATION CONTROL : System Diagram12.
METER ILLUMINATION CONTROL : System Description12, mETER EFFECT FUNCTION : System Diagram13, mETER EFFECT FUNCTION : System Description13, sHIFT POSITION INDICATOR : System Diagram 11.
SHIFT POSITION INDICATOR : System Description 11, oIL PRESSURE WARNING LAMP : System Diagram 12, tHE FUEL GAUGE INDICATOR DOES NOT, pOWER SUPPLY AND GROUND CIRCUIT 50.
COMBINATION METER : Diagnosis Procedure 50, fUEL LEVEL SENSOR SIGNAL CIRCUIT 51, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precautions for Removing Battery Terminal.
When removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch.
If the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error.
METER SYSTEM : Component Parts Location, refer to "ENGINE CONTROL SYSTEM , aBS actuator and electric unit (control unit), sYSTEM : Component Parts Location" (WITH INTELLIGENT KEY.
SYSTEM : Component Parts Location" (WITHOUT INTELLIGENT KEY, provides the driver with various kinds of vehicle information via the CAN communication line, the use of signals through hard wire, includes the signal buffer to transmit received signals other units.
Transmits the following signals to the combination meter via CAN communication, fuel filler cap warning display signal, oil pressure warning lamp signal.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3, mETER SYSTEM : Component Parts Location 5, mETER SYSTEM : Component Description 6.
METER SYSTEM : System Diagram 7, mETER SYSTEM : System Description 7, oIL PRESSURE WARNING LAMP : System Description12, mETER ILLUMINATION CONTROL : System Diagram12.
METER ILLUMINATION CONTROL : System Description12, mETER EFFECT FUNCTION : System Diagram13, mETER EFFECT FUNCTION : System Description13, sHIFT POSITION INDICATOR : System Diagram 11.
SHIFT POSITION INDICATOR : System Description 11, oIL PRESSURE WARNING LAMP : System Diagram 12, tHE FUEL GAUGE INDICATOR DOES NOT, pOWER SUPPLY AND GROUND CIRCUIT 50.
COMBINATION METER : Diagnosis Procedure 50, fUEL LEVEL SENSOR SIGNAL CIRCUIT 51, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.
Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.
Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.
Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, precautions for Removing Battery Terminal.
When removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may, for vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch.
If the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC, the removal of 12V battery may cause DTC detection error.
METER SYSTEM : Component Parts Location, refer to "ENGINE CONTROL SYSTEM , aBS actuator and electric unit (control unit), sYSTEM : Component Parts Location" (WITH INTELLIGENT KEY.
SYSTEM : Component Parts Location" (WITHOUT INTELLIGENT KEY, provides the driver with various kinds of vehicle information via the CAN communication line, the use of signals through hard wire, includes the signal buffer to transmit received signals other units.
Transmits the following signals to the combination meter via CAN communication, fuel filler cap warning display signal, oil pressure warning lamp signal.
Nissan Models