2014 Nissan Frontier - Enging Cooling System (Section CO) (59 pages)
Download Enging Cooling System (Section CO)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, wATER OUTLET AND WATER PIPING 28, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"31, removal and Installation (Crankshaft driven type) 19.
WATER INLET AND THERMOSTAT ASSEMBLY 55, removal and Installation (Crankshaft driven type) 47, removal and Installation (Motor driven type) 48, wATER OUTLET AND WATER PIPING 57.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, after removing the bolts and nuts, separate mating surface, remove the old liquid gasket using Tool.
Do not damage mating surfaces, tap the seal cutter insert it (1), in areas where the Tool is difficult to use, lightly tap slide it (2), surface and the mating surface using suitable tool.
Remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes, attach the liquid gasket tube suitable tool, use Genuine RTV Silicone Sealant equivalent.
Apply the liquid gasket without breaks specified location, normally apply the liquid gasket on the inside edge bolt, within five minutes of liquid gasket application, install mating component, if the liquid gasket protrudes, wipe it off immediately.
Do not retighten after installation, wait minutes or more after installation before refilling, if there are more specific instructions in the procedures contained in manual concerning liquid, the actual shape of the tools may differ those illustrated here.
Removing chain tensioner cover water, adapting radiator cap tester radiator cap, adapting radiator cap tester reservoir filler, adapting radiator cap tester reservoir cap.
Pressing the tube liquid gasket, o-ring for damage, deterioration improper fitting, exhaust gas leaks into coolCylinder head gasket deteriing system, driving in low gear extended time.
Occur from high pressure fluid escaping from radiator reservoir, wrap a thick cloth around the cap, check if the engine coolant reservoir tank level within MIN, adjust engine coolant level necessary.
Do not remove the radiator cap or reservoir cap when the engine is hot, from high pressure coolant escaping from radiator reservoir, to check for leakage, apply pressure to the cooling system.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, wATER OUTLET AND WATER PIPING 28, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"31, removal and Installation (Crankshaft driven type) 19.
WATER INLET AND THERMOSTAT ASSEMBLY 55, removal and Installation (Crankshaft driven type) 47, removal and Installation (Motor driven type) 48, wATER OUTLET AND WATER PIPING 57.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, after removing the bolts and nuts, separate mating surface, remove the old liquid gasket using Tool.
Do not damage mating surfaces, tap the seal cutter insert it (1), in areas where the Tool is difficult to use, lightly tap slide it (2), surface and the mating surface using suitable tool.
Remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes, attach the liquid gasket tube suitable tool, use Genuine RTV Silicone Sealant equivalent.
Apply the liquid gasket without breaks specified location, normally apply the liquid gasket on the inside edge bolt, within five minutes of liquid gasket application, install mating component, if the liquid gasket protrudes, wipe it off immediately.
Do not retighten after installation, wait minutes or more after installation before refilling, if there are more specific instructions in the procedures contained in manual concerning liquid, the actual shape of the tools may differ those illustrated here.
Removing chain tensioner cover water, adapting radiator cap tester radiator cap, adapting radiator cap tester reservoir filler, adapting radiator cap tester reservoir cap.
Pressing the tube liquid gasket, o-ring for damage, deterioration improper fitting, exhaust gas leaks into coolCylinder head gasket deteriing system, driving in low gear extended time.
Occur from high pressure fluid escaping from radiator reservoir, wrap a thick cloth around the cap, check if the engine coolant reservoir tank level within MIN, adjust engine coolant level necessary.
Do not remove the radiator cap or reservoir cap when the engine is hot, from high pressure coolant escaping from radiator reservoir, to check for leakage, apply pressure to the cooling system.
Nissan Models