2014 Nissan Frontier - Accelerator Control System (Section ACC) (5 pages)
Download Accelerator Control System (Section ACC)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, < UNIT REMOVAL AND INSTALLATION >.
Avoid damage from dropping the accelerator pedal assembly during handling, keep the accelerator pedal assembly away water, disconnect the harness connector accelerator position, pull the connector lock back to unlock connector.
Accelerator pedal position sensor shown, pull up on the connector to disconnect it accelerator, remove the two upper and one lower accelerator pedal nuts, installation is in the reverse order removal.
Check that the accelerator pedal moves smoothly within specified range, check that the accelerator pedal smoothly returns original, perform an electrical inspection of accelerator pedal position, whenever the harness connector accelerator pedal.
Position sensor is disconnected, perform ″Accelerator Pedal Released Position Learning″, "Accelerator Pedal Released Position Learning" (QR25DE), EC-590, "Accelerator Pedal, reset the steering angle sensor calibration, aNGLE SENSOR NEUTRAL POSITION : Special Repair Requirement" (Type 1) BRC-124.
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement" (Type 2), sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total pedal applied stroke (A).
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, < UNIT REMOVAL AND INSTALLATION >.
Avoid damage from dropping the accelerator pedal assembly during handling, keep the accelerator pedal assembly away water, disconnect the harness connector accelerator position, pull the connector lock back to unlock connector.
Accelerator pedal position sensor shown, pull up on the connector to disconnect it accelerator, remove the two upper and one lower accelerator pedal nuts, installation is in the reverse order removal.
Check that the accelerator pedal moves smoothly within specified range, check that the accelerator pedal smoothly returns original, perform an electrical inspection of accelerator pedal position, whenever the harness connector accelerator pedal.
Position sensor is disconnected, perform ″Accelerator Pedal Released Position Learning″, "Accelerator Pedal Released Position Learning" (QR25DE), EC-590, "Accelerator Pedal, reset the steering angle sensor calibration, aNGLE SENSOR NEUTRAL POSITION : Special Repair Requirement" (Type 1) BRC-124.
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement" (Type 2), sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS), accelerator pedal - total pedal applied stroke (A).
Nissan Models