2011 Nissan Frontier - Rear Axle (Section RAX) (25 pages)
Download Rear Axle (Section RAX)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"15, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
When installing rubber parts, final tightening must be carried out under unladen condition* with tires, *: Fuel, radiator coolant and engine oil full, after installing removed suspension parts, check wheel alignment adjust necessary, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Removing wheel bearing, wheel bearing lock, a: ABS sensor mount repair kit J46215-8, b: Plastic plugs nuts kit J-46215-4, removing and installing each brake piping.
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, use the chart below to help you find the cause of the symptom, check the axle parts for excessive play, wear and damage, shake each rear wheel to check for excessive play.
Retighten all nuts and bolts to the specified torque, check that the axle shaft bearing operates smoothly, before removing the rear axle, disconnect the wheel sensor from the assembly, wheel bearing does not require maintenance.
If growling noise is emitted from wheel bearing during operation, replace wheel bearing assembly, if the wheel bearing assembly is removed, it must be replaced, and Installation" (Type 1), BRC-176, "Removal and Installation" (Type 2) BRC-295, "Removal Installation" (Type 3), remove the axle oil seal using Tools shown.
Install a new axle oil seal, apply a constant pressure on the slide hammer while turning, the slide hammer 180° degrees periodically while pulling, always replace the wheel sensor rotor with new one.
Always replace the snap ring and shim washer with new ones, always replace the bearing ring retainer with new one, check axle shaft for straightness, cracks, damage, wear and distortion, check axle case for yield, deformation and cracks.
Install the grease catcher axle shaft, install the wheel studs through the grease catcher into the axle shaft using suitable press, all six wheel studs must be pressed on at the same time and are flush with grease catcher when, position the axle bearing on the back plate torque member.
Install the axle bearing studs using a suitable press to attach the axle bearing to the back plate torque, always replace the axle bearing with new one, install the back plate and torque member, new axle bearing, new bearing ring retainer on the axle shaft using suitable.
Press the new bearing ring retainer on axle shaft with, the taper side positioned shown, select the correct size shim washer.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, (SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"15, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
When installing rubber parts, final tightening must be carried out under unladen condition* with tires, *: Fuel, radiator coolant and engine oil full, after installing removed suspension parts, check wheel alignment adjust necessary, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Removing wheel bearing, wheel bearing lock, a: ABS sensor mount repair kit J46215-8, b: Plastic plugs nuts kit J-46215-4, removing and installing each brake piping.
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, use the chart below to help you find the cause of the symptom, check the axle parts for excessive play, wear and damage, shake each rear wheel to check for excessive play.
Retighten all nuts and bolts to the specified torque, check that the axle shaft bearing operates smoothly, before removing the rear axle, disconnect the wheel sensor from the assembly, wheel bearing does not require maintenance.
If growling noise is emitted from wheel bearing during operation, replace wheel bearing assembly, if the wheel bearing assembly is removed, it must be replaced, and Installation" (Type 1), BRC-176, "Removal and Installation" (Type 2) BRC-295, "Removal Installation" (Type 3), remove the axle oil seal using Tools shown.
Install a new axle oil seal, apply a constant pressure on the slide hammer while turning, the slide hammer 180° degrees periodically while pulling, always replace the wheel sensor rotor with new one.
Always replace the snap ring and shim washer with new ones, always replace the bearing ring retainer with new one, check axle shaft for straightness, cracks, damage, wear and distortion, check axle case for yield, deformation and cracks.
Install the grease catcher axle shaft, install the wheel studs through the grease catcher into the axle shaft using suitable press, all six wheel studs must be pressed on at the same time and are flush with grease catcher when, position the axle bearing on the back plate torque member.
Install the axle bearing studs using a suitable press to attach the axle bearing to the back plate torque, always replace the axle bearing with new one, install the back plate and torque member, new axle bearing, new bearing ring retainer on the axle shaft using suitable.
Press the new bearing ring retainer on axle shaft with, the taper side positioned shown, select the correct size shim washer.
Nissan Models