2007 Nissan Frontier - Manual Transmission (Section MT) (120 pages)
Download Manual Transmission (Section MT)
Manual Description
OIL LEAKAGE AND OIL LEVEL 9, removal and Installation Vehicle 15, sERVICE DATA AND SPECIFICATIONS (SDS) 48, mAIN DRIVE GEAR SNAP RING 49.
COUNTER GEAR REAR SNAP RING 49, oIL LEAKAGE AND OIL LEVEL 59, removal and Installation Vehicle (For 2WD, removal and Installation Vehicle (For 4WD.
SERVICE DATA AND SPECIFICATIONS (SDS) 118, do not reuse transmission oil once it has been drained, check oil level or replace oil with vehicle level surface, during removal or installation, keep inside of transmission clear dust dirt.
Check for the correct installation status prior to removal or disassembly, be certain they do not interfere with the function of the parts they applied to, in principle, tighten nuts and bolts gradually in several steps working diagonally from inside outside, tightening sequence specified, use it.
Be careful not to damage sliding surfaces mating surfaces, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removing counter gear rear thrust bearing, removing counter gear front bearing (Use.
Installing counter gear rear end bearing, installing mainshaft counter gear (Use, removing and installing mainshaft rear bearing (Use with J-25726-B), removing and installing mainshaft rear bearing (Use with J-26349-A).
Removing counter gear rear end bearing, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, hard to shift will not shift, cHECK PLUG RETURN SPRING AND CHECK BALL (Worn damaged).
Use the chart below to help you find the cause of the problem, start the engine and let it run to warm up transmission, specified limit near filler plug hole, after refilling the oil, check oil level.
Plug, then install it to the transmission, make sure that oil is not leaking from the transmission around it, check oil level from the filler plug hole shown, do not start engine while checking oil level.
Tighten the filler plug to the specified torque, remove the rear oil seal using Tool, do not reuse rear oil seal, installation is the reverse order removal.
Drive the new oil seal straight until it stops using Tool, g Do not reuse rear oil seal, g Apply multi-purpose grease to oil seal lips before installing, g Do not incline rear oil seal during installation.
Check the transmission oil level after installation, remove the cup holder finisher and shift bezel, remove the retaining plate dust boot covers, remove the clip (B) and then separate the boot control housing.
Remove the shift lever assembly transmission, do not reuse the clip snap ring, apply cement to threads of shift lever assembly, when shift lever assembly is shifted to each position, make sure there is no binding disconnection.
Refer to the figure below for air breather hose removal installation information, make sure there are no pinched or blocked areas on the air breather hose after installation, when inserting the air breather hose, be sure to insert it fully until its end reaches end.
Manual Description
OIL LEAKAGE AND OIL LEVEL 9, removal and Installation Vehicle 15, sERVICE DATA AND SPECIFICATIONS (SDS) 48, mAIN DRIVE GEAR SNAP RING 49.
COUNTER GEAR REAR SNAP RING 49, oIL LEAKAGE AND OIL LEVEL 59, removal and Installation Vehicle (For 2WD, removal and Installation Vehicle (For 4WD.
SERVICE DATA AND SPECIFICATIONS (SDS) 118, do not reuse transmission oil once it has been drained, check oil level or replace oil with vehicle level surface, during removal or installation, keep inside of transmission clear dust dirt.
Check for the correct installation status prior to removal or disassembly, be certain they do not interfere with the function of the parts they applied to, in principle, tighten nuts and bolts gradually in several steps working diagonally from inside outside, tightening sequence specified, use it.
Be careful not to damage sliding surfaces mating surfaces, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removing counter gear rear thrust bearing, removing counter gear front bearing (Use.
Installing counter gear rear end bearing, installing mainshaft counter gear (Use, removing and installing mainshaft rear bearing (Use with J-25726-B), removing and installing mainshaft rear bearing (Use with J-26349-A).
Removing counter gear rear end bearing, nOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING, hard to shift will not shift, cHECK PLUG RETURN SPRING AND CHECK BALL (Worn damaged).
Use the chart below to help you find the cause of the problem, start the engine and let it run to warm up transmission, specified limit near filler plug hole, after refilling the oil, check oil level.
Plug, then install it to the transmission, make sure that oil is not leaking from the transmission around it, check oil level from the filler plug hole shown, do not start engine while checking oil level.
Tighten the filler plug to the specified torque, remove the rear oil seal using Tool, do not reuse rear oil seal, installation is the reverse order removal.
Drive the new oil seal straight until it stops using Tool, g Do not reuse rear oil seal, g Apply multi-purpose grease to oil seal lips before installing, g Do not incline rear oil seal during installation.
Check the transmission oil level after installation, remove the cup holder finisher and shift bezel, remove the retaining plate dust boot covers, remove the clip (B) and then separate the boot control housing.
Remove the shift lever assembly transmission, do not reuse the clip snap ring, apply cement to threads of shift lever assembly, when shift lever assembly is shifted to each position, make sure there is no binding disconnection.
Refer to the figure below for air breather hose removal installation information, make sure there are no pinched or blocked areas on the air breather hose after installation, when inserting the air breather hose, be sure to insert it fully until its end reaches end.
Nissan Models