2006 Nissan Frontier - Parking Brake System (Section PB) (10 pages)
Download Parking Brake System (Section PB)
Manual Description
SERVICE DATA AND SPECIFICATIONS (SDS) 9, measuring rear rotor drum parking, when parking brake lever is operated with the specified force, make sure the stroke within specified, make sure the components are attached properly, checking looseness backlash.
Check parking brake lever assembly for bends, damage and cracks, replace necessary, check cable for wear and damage, replace necessary, check parking brake warning lamp switch for malfunction, and replace if necessary, remove rear half of the center console.
Rotate adjusting nut and loosen cable until tension sufficiently, remove the wheel and tire using power tool, remove the rotor and measure inner diameter widest point, using wheel nuts, secure the disc to the hub prevent it.
Rotate disc rotor to make sure there no drag, operate parking brake lever 10 or more times with force 490, rotate adjusting nut to adjust lever stroke specification, with parking brake lever completely disengaged, make sure.
There is no drag parking brake, remove right and left rear cables equalizer, remove front parking brake cable bolts under vehicle, remove rear half of center console.
Remove four control lever assembly bolts, then remove control lever assembly, remove the front cable grommet and cover control lever assembly, remove front cable to control lever assembly bolt, remove the control lever assembly adjusting nut, then remove front cable.
Do not reuse adjusting nut after removing it, installation is in the reverse order removal, q Do not reuse adjusting nut after removal, q Install the control lever assembly bolts criss-cross pattern.
Clean the brakes with a vacuum dust collector to minimize the hazard of airborne particles other, remove the disc rotor only with the parking brake lever completely disengaged, check shoe sliding surface for excessive wear damage, check anti-rattle pin for excessive wear corrosion.
When disassembling adjuster, apply PBC (Poly Butyl Cuprysil) grease or equivalent adjuster, check either visually or with a vernier caliper to see if there is any excessive wear, cracks, damage, apply brake grease to the specified points during assembly, install adjuster so that threaded part expands when rotating it.
The direction shown by arrow, shorten adjuster by rotating it in the opposite direction shown, after replacing brake shoes or disc rotors, or parking brake does, not function well, perform break-in operation follows.
Perform parking brake burnishing operation by driving the vehicle forward under following conditions, vehicle speed km/h (25 MPH) set (forward), parking brake operating force 196 N (20, to prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after.
Q Do not perform excessive break-in operations, because it may cause uneven early wear, after burnishing operation, check parking brake lever stroke, sERVICE DATA AND SPECIFICATIONS (SDS), number of notches [under force of 196 N (20.
Number of notches when warning lamp switch comes...
Manual Description
SERVICE DATA AND SPECIFICATIONS (SDS) 9, measuring rear rotor drum parking, when parking brake lever is operated with the specified force, make sure the stroke within specified, make sure the components are attached properly, checking looseness backlash.
Check parking brake lever assembly for bends, damage and cracks, replace necessary, check cable for wear and damage, replace necessary, check parking brake warning lamp switch for malfunction, and replace if necessary, remove rear half of the center console.
Rotate adjusting nut and loosen cable until tension sufficiently, remove the wheel and tire using power tool, remove the rotor and measure inner diameter widest point, using wheel nuts, secure the disc to the hub prevent it.
Rotate disc rotor to make sure there no drag, operate parking brake lever 10 or more times with force 490, rotate adjusting nut to adjust lever stroke specification, with parking brake lever completely disengaged, make sure.
There is no drag parking brake, remove right and left rear cables equalizer, remove front parking brake cable bolts under vehicle, remove rear half of center console.
Remove four control lever assembly bolts, then remove control lever assembly, remove the front cable grommet and cover control lever assembly, remove front cable to control lever assembly bolt, remove the control lever assembly adjusting nut, then remove front cable.
Do not reuse adjusting nut after removing it, installation is in the reverse order removal, q Do not reuse adjusting nut after removal, q Install the control lever assembly bolts criss-cross pattern.
Clean the brakes with a vacuum dust collector to minimize the hazard of airborne particles other, remove the disc rotor only with the parking brake lever completely disengaged, check shoe sliding surface for excessive wear damage, check anti-rattle pin for excessive wear corrosion.
When disassembling adjuster, apply PBC (Poly Butyl Cuprysil) grease or equivalent adjuster, check either visually or with a vernier caliper to see if there is any excessive wear, cracks, damage, apply brake grease to the specified points during assembly, install adjuster so that threaded part expands when rotating it.
The direction shown by arrow, shorten adjuster by rotating it in the opposite direction shown, after replacing brake shoes or disc rotors, or parking brake does, not function well, perform break-in operation follows.
Perform parking brake burnishing operation by driving the vehicle forward under following conditions, vehicle speed km/h (25 MPH) set (forward), parking brake operating force 196 N (20, to prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after.
Q Do not perform excessive break-in operations, because it may cause uneven early wear, after burnishing operation, check parking brake lever stroke, sERVICE DATA AND SPECIFICATIONS (SDS), number of notches [under force of 196 N (20.
Number of notches when warning lamp switch comes...
Nissan Models