2006 Nissan Frontier - General Information (Section GI) (58 pages)
Download General Information (Section GI)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, precautions for Three Way Catalyst 5, precautions for Multiport Fuel Injection System, hOW TO USE THIS MANUAL 8.
Relation between Illustrations Descriptions 9, how to Follow Trouble Diagnoses 10, hOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES 12, kEY TO SYMBOLS SIGNIFYING MEASUREMENTS OR PROCEDURES 14.
How to Read Wiring Diagrams 16, sAMPLE/WIRING DIAGRAM - EXAMPL - 17, sERVICE INFORMATION FOR ELECTRICAL INCIDENT 25, cONNECTOR AND TERMINAL PIN KIT 25.
How to Perform Efficient Diagnosis an Electrical, control Units Electrical Parts 36, nickel Metal Hydride Battery Replacement 39, cONSULT-II Data Link Connector (DLC) Circuit 41.
Garage Jack Safety Stand 43, vehicle Recovery (Freeing stuck vehicle) 46, tIGHTENING TORQUE OF STANDARD BOLTS 47, recommended Chemical Products Sealants 48.
Observe the following precautions to ensure safe and proper servicing, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, do not operate the engine for an extended period time without, keep the work area well ventilated and free any inflammable.
Inflammable or poisonous materials, such as gasoline, refrigerant gas, etc, sure to properly ventilate the area before working with hazardous materials, do not smoke while working vehicle, before jacking up the vehicle, apply wheel chocks other tire.
Blocks to the wheels to prevent the vehicle moving, jacking up the vehicle, support the vehicle weight with safety, stands at the points designated for proper lifting before working, these operations should be done level surface.
When removing a heavy component such as the engine or transaxle/transmission, be careful not to lose your balance drop, the brake tubes master cylinder, before starting repairs which do not require battery power, if the battery terminals are disconnected, recorded memory.
Radio and each control unit erased, avoid contact with hot metal parts, do not remove the radiator cap when engine hot, dispose of drained oil or the solvent used cleaning parts.
Continued refueling may cause fuel overflow, resulting fuel, clean all disassembled parts in the designated liquid solvent, replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc, replace inner and outer races of tapered roller bearings and needle bearings set.
Arrange the disassembled parts in accordance with their assembled locations sequence, do not touch the terminals of electrical components which use microcomputers (such ECM), static electricity may damage internal electronic components.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, precautions for Three Way Catalyst 5, precautions for Multiport Fuel Injection System, hOW TO USE THIS MANUAL 8.
Relation between Illustrations Descriptions 9, how to Follow Trouble Diagnoses 10, hOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES 12, kEY TO SYMBOLS SIGNIFYING MEASUREMENTS OR PROCEDURES 14.
How to Read Wiring Diagrams 16, sAMPLE/WIRING DIAGRAM - EXAMPL - 17, sERVICE INFORMATION FOR ELECTRICAL INCIDENT 25, cONNECTOR AND TERMINAL PIN KIT 25.
How to Perform Efficient Diagnosis an Electrical, control Units Electrical Parts 36, nickel Metal Hydride Battery Replacement 39, cONSULT-II Data Link Connector (DLC) Circuit 41.
Garage Jack Safety Stand 43, vehicle Recovery (Freeing stuck vehicle) 46, tIGHTENING TORQUE OF STANDARD BOLTS 47, recommended Chemical Products Sealants 48.
Observe the following precautions to ensure safe and proper servicing, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, do not operate the engine for an extended period time without, keep the work area well ventilated and free any inflammable.
Inflammable or poisonous materials, such as gasoline, refrigerant gas, etc, sure to properly ventilate the area before working with hazardous materials, do not smoke while working vehicle, before jacking up the vehicle, apply wheel chocks other tire.
Blocks to the wheels to prevent the vehicle moving, jacking up the vehicle, support the vehicle weight with safety, stands at the points designated for proper lifting before working, these operations should be done level surface.
When removing a heavy component such as the engine or transaxle/transmission, be careful not to lose your balance drop, the brake tubes master cylinder, before starting repairs which do not require battery power, if the battery terminals are disconnected, recorded memory.
Radio and each control unit erased, avoid contact with hot metal parts, do not remove the radiator cap when engine hot, dispose of drained oil or the solvent used cleaning parts.
Continued refueling may cause fuel overflow, resulting fuel, clean all disassembled parts in the designated liquid solvent, replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc, replace inner and outer races of tapered roller bearings and needle bearings set.
Arrange the disassembled parts in accordance with their assembled locations sequence, do not touch the terminals of electrical components which use microcomputers (such ECM), static electricity may damage internal electronic components.
Nissan Models