2006 Nissan Frontier - Body, Lock & Security System (Section BL) (222 pages)
Download Body, Lock & Security System (Section BL)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, sQUEAK AND RATTLE TROUBLE DIAGNOSES 6, dUPLICATE THE NOISE AND TEST DRIVE 7, lOCATE THE NOISE AND IDENTIFY THE.
Generic Squeak Rattle Troubleshooting 8, oVERHEAD CONSOLE (FRONT AND REAR) 9, removal and Installation Hood Assembly 13, removal and Installation of Hood Lock Control 14.
Component Parts and Harness Connector Location 16, wiring Diagram — D/LOCK — (King Cab) 21, wiring Diagram — D/LOCK — (Crew Cab) 27, terminals and Reference Value BCM 31.
BCM Power Supply and Ground Circuit Check 34, door Switch Check (King Cab) 34, door Switch Check (Crew Cab) 36, front Door Lock Assembly LH (Actuator) Check 42.
Front Door Lock Actuator RH Check 43, rear Door Lock Actuator RH/LH Check (Crew Cab) 44, front Door Lock Assembly LH (Key Cylinder Switch), component Parts and Harness Connector Location 47.
Wiring Diagram — KEYLES — (King Cab) 52, wiring Diagram — KEYLES — (Crew Cab) 57, terminals and Reference Value BCM 60, terminals and Reference Value IPDM E/R 60.
Door Switch Check (King Cab) 68, door Switch Check (Crew Cab) 70, keyfob Battery Function Check 71, remote Keyless Entry Receiver System Check 72.
Check Room Lamp Illumination Function 75, kEYFOB ID SET UP WITH CONSULT-II 76, kEYFOB ID SET UP WITHOUT CONSULT-II 78, vEHICLE SECURITY (THEFT WARNING) SYSTEM 80.
Component Parts and Harness Connector Location 80, pOWER SUPPLY AND GROUND CIRCUIT 81, iNITIAL CONDITION TO ACTIVATE THE SYSTEM 82, vEHICLE SECURITY SYSTEM ALARM OPERATION 82.
Wiring Diagram — VEHSEC — (King Cab) 85, wiring Diagram — VEHSEC — (Crew Cab) 92, terminals and Reference Value BCM 97, terminals and Reference Value IPDM E/R 97.
Component Parts Harness Connector Location, wiring Diagram — NATS — 126, terminals and Reference Value BCM 128, cONSULT-II DIAGNOSTIC TEST MODE FUNCTION 129.
How to Replace NATS Antenna Amp 142, wiring Diagram — TRNSCV — 143, precautions in Repairing High Strength Steel 191, hIGH STRENGTH STEEL (HSS) USED IN NISSAN VEHICLES 191.
CENTER PILLAR (CREW CAB ONLY) 200, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, sQUEAK AND RATTLE TROUBLE DIAGNOSES 6, dUPLICATE THE NOISE AND TEST DRIVE 7, lOCATE THE NOISE AND IDENTIFY THE.
Generic Squeak Rattle Troubleshooting 8, oVERHEAD CONSOLE (FRONT AND REAR) 9, removal and Installation Hood Assembly 13, removal and Installation of Hood Lock Control 14.
Component Parts and Harness Connector Location 16, wiring Diagram — D/LOCK — (King Cab) 21, wiring Diagram — D/LOCK — (Crew Cab) 27, terminals and Reference Value BCM 31.
BCM Power Supply and Ground Circuit Check 34, door Switch Check (King Cab) 34, door Switch Check (Crew Cab) 36, front Door Lock Assembly LH (Actuator) Check 42.
Front Door Lock Actuator RH Check 43, rear Door Lock Actuator RH/LH Check (Crew Cab) 44, front Door Lock Assembly LH (Key Cylinder Switch), component Parts and Harness Connector Location 47.
Wiring Diagram — KEYLES — (King Cab) 52, wiring Diagram — KEYLES — (Crew Cab) 57, terminals and Reference Value BCM 60, terminals and Reference Value IPDM E/R 60.
Door Switch Check (King Cab) 68, door Switch Check (Crew Cab) 70, keyfob Battery Function Check 71, remote Keyless Entry Receiver System Check 72.
Check Room Lamp Illumination Function 75, kEYFOB ID SET UP WITH CONSULT-II 76, kEYFOB ID SET UP WITHOUT CONSULT-II 78, vEHICLE SECURITY (THEFT WARNING) SYSTEM 80.
Component Parts and Harness Connector Location 80, pOWER SUPPLY AND GROUND CIRCUIT 81, iNITIAL CONDITION TO ACTIVATE THE SYSTEM 82, vEHICLE SECURITY SYSTEM ALARM OPERATION 82.
Wiring Diagram — VEHSEC — (King Cab) 85, wiring Diagram — VEHSEC — (Crew Cab) 92, terminals and Reference Value BCM 97, terminals and Reference Value IPDM E/R 97.
Component Parts Harness Connector Location, wiring Diagram — NATS — 126, terminals and Reference Value BCM 128, cONSULT-II DIAGNOSTIC TEST MODE FUNCTION 129.
How to Replace NATS Antenna Amp 142, wiring Diagram — TRNSCV — 143, precautions in Repairing High Strength Steel 191, hIGH STRENGTH STEEL (HSS) USED IN NISSAN VEHICLES 191.
CENTER PILLAR (CREW CAB ONLY) 200, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
Nissan Models