2004 Nissan Frontier - Engine Mechanical (Section EM) (154 pages)
Download Engine Mechanical (Section EM)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, rEMOVAL OF LIQUID GASKET SEALING 5, vALVE LIFTER AND ADJUSTING SHIM 41, pISTON AND PISTON PIN CLEARANCE 50.
CONNECTING ROD BEND AND TORSION 51, cYLINDER BLOCK DISTORTION AND WEAR 52, sERVICE DATA AND SPECIFICATIONS (SDS) 63, piston, Piston Ring Piston pin 69.
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 72, rEMOVAL OF LIQUID GASKET SEALING 73, noise, Vibration Harshness (NVH) 78, rOCKER SHAFT AND ROCKER ARM 116.
PISTON AND PISTON PIN CLEARANCE 133, cONNECTING ROD BEND AND TORSION 134, cYLINDER BLOCK DISTORTION AND WEAR 134, rEPLACING PILOT BUSHING (M/T) OR PILOT.
SERVICE DATA AND SPECIFICATIONS (SDS) 144, rOCKER SHAFT AND ROCKER ARM 146, piston, Piston Ring Piston Pin 150, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, equipped with dual stage front air bag modules, the SRS system uses the seat belt switches determine, front air bag deployment, and may only deploy one front air bag, depending on the severity collision.
Whether the front occupants are belted or unbelted, the vehicle may be equipped with a passenger air bag deactivation switch, a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that, rear-facing child restraint can be used in the front passenger seat.
Enabled and could inflate for certain types of collision, up when the passenger air bag is switched OFF, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system.
Do not use electrical test equipment on any circuit related to the SRS unless instructed, the vehicle may be equipped with a passenger air bag deactivation switch which can be operated, and could inflate for certain types of collision, passenger air bag deactivation switch is in the same position (ON or OFF) when vehicle.
Use an angle wrench for the final tightening of following engine parts, the torque value for these parts are preliminary step, ensure thread and seat surfaces are clean and coated with engine oil, after removing the mounting bolts and nuts, disconnect the component using seal cutter.
Be careful not to damage mating surfaces, use a plastic hammer to lightly tap (1) the areas where liquid, to slide the cutter along joint, if for some unavoidable reason a tool such flat-bladed.
Screwdriver is used, be careful not to damage mating surfaces, using a scraper, remove the old liquid gasket adhering, gasket application surface mating surface, q Remove the sealant completely from the groove gasket.
Application surface, mounting bolts, bolt holes, thoroughly clean the gasket application surface and the mating surface remove adhering moisture, attach the sealant tube tube presser, apply the sealant without breaks to specified location with.
Make sure to read the text manual, q Within five minutes of the sealant application install mating component, q If the sealant protrudes, wipe it off immediately.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 4, rEMOVAL OF LIQUID GASKET SEALING 5, vALVE LIFTER AND ADJUSTING SHIM 41, pISTON AND PISTON PIN CLEARANCE 50.
CONNECTING ROD BEND AND TORSION 51, cYLINDER BLOCK DISTORTION AND WEAR 52, sERVICE DATA AND SPECIFICATIONS (SDS) 63, piston, Piston Ring Piston pin 69.
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 72, rEMOVAL OF LIQUID GASKET SEALING 73, noise, Vibration Harshness (NVH) 78, rOCKER SHAFT AND ROCKER ARM 116.
PISTON AND PISTON PIN CLEARANCE 133, cONNECTING ROD BEND AND TORSION 134, cYLINDER BLOCK DISTORTION AND WEAR 134, rEPLACING PILOT BUSHING (M/T) OR PILOT.
SERVICE DATA AND SPECIFICATIONS (SDS) 144, rOCKER SHAFT AND ROCKER ARM 146, piston, Piston Ring Piston Pin 150, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, equipped with dual stage front air bag modules, the SRS system uses the seat belt switches determine, front air bag deployment, and may only deploy one front air bag, depending on the severity collision.
Whether the front occupants are belted or unbelted, the vehicle may be equipped with a passenger air bag deactivation switch, a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that, rear-facing child restraint can be used in the front passenger seat.
Enabled and could inflate for certain types of collision, up when the passenger air bag is switched OFF, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system.
Do not use electrical test equipment on any circuit related to the SRS unless instructed, the vehicle may be equipped with a passenger air bag deactivation switch which can be operated, and could inflate for certain types of collision, passenger air bag deactivation switch is in the same position (ON or OFF) when vehicle.
Use an angle wrench for the final tightening of following engine parts, the torque value for these parts are preliminary step, ensure thread and seat surfaces are clean and coated with engine oil, after removing the mounting bolts and nuts, disconnect the component using seal cutter.
Be careful not to damage mating surfaces, use a plastic hammer to lightly tap (1) the areas where liquid, to slide the cutter along joint, if for some unavoidable reason a tool such flat-bladed.
Screwdriver is used, be careful not to damage mating surfaces, using a scraper, remove the old liquid gasket adhering, gasket application surface mating surface, q Remove the sealant completely from the groove gasket.
Application surface, mounting bolts, bolt holes, thoroughly clean the gasket application surface and the mating surface remove adhering moisture, attach the sealant tube tube presser, apply the sealant without breaks to specified location with.
Make sure to read the text manual, q Within five minutes of the sealant application install mating component, q If the sealant protrudes, wipe it off immediately.
Nissan Models