2002 Nissan Frontier - Cooling Systems (Section LC) (36 pages)
Download Cooling Systems (Section LC)
Manual Description
″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″3, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″9, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″19, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″26.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG” AND SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER” used along with, a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger frontal collision, the Supplemental Restraint System consists of air bag modules (located in the center steering wheel.
And in the instrument panel on the passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness, spiral cable, the vehicle (except Crew Cab model) is equipped with a passenger air bag deactivation switch, rear seat exists where a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a rear-facing child restraint can be used in the front passenger seat, located in the center of the instrument panel, near the ashtray.
Position, the passenger air bag is disabled and will not inflate in a frontal collision, indicator on the instrument panel lights up when the passenger air bag is switched OFF, always remains enabled and is not affected by the passenger air bag deactivation switch, information necessary to service the system safely is included in the RS section Service Manual.
¼ To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, ¼ Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, ¼ The vehicle (except Crew Cab model) is equipped with a passenger air bag deactivation switch, which can be operated by the customer.
Switched ON, the passenger air bag is enabled and could inflate in a frontal collision, maintenance or repair, make sure the passenger air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived service, use a scraper to remove all traces of old liquid gasket, apply a continuous bead of liquid gasket mating surfaces.
(Use Genuine Silicone RTV or equivalent, for oil pan, be sure liquid gasket diameter is 3, for areas except oil pan, be sure liquid gasket diameter 2, apply liquid gasket around the inner side bolt holes (unless.
Assembly should be done within 5 minutes after coating, wait at least 30 minutes before refilling engine oil engine, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, pressing the tube liquid gasket.
A/T models, put selector lever Park P” position, if difference is extreme, check oil passage oil pump, install oil pressure switch with sealant, always replace with new oil seal gasket.
When removing oil pump, turn crankshaft so that No, when installing oil pump, apply engine oil gears, then, align punch mark on drive spindle and oil hole oil, visually inspect components wear damage.
Check oil pressure regulator valve sliding surface valve, coat regulator valve with engine oil, smoothly into the valve hole by its own weight, replace regulator valve set or oil pump assembly, damaged.
¼ Use Tool KV10115801 (J38956) removing oil filter, using a feeler gauge, check following clearances, outer rotor body clearance 2, if body to rotor clearances (2, 3) exceed limit, replace.
Regulator valve to oil pump cover clearance, adapting radiator cap tester radiator filler neck, ¼ Never remove the radiator cap when engine hot, serious burns could occur high pressure coolant.
¼ Wrap a thick cloth around the radiator cap, a quarter turn to allow built-up pressure to escape, check radiator for mud or clogging.
Manual Description
″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″3, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″9, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″19, ″AIR BAG″ AND ″SEAT BELT PRE-TENSIONER″26.
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG” AND SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER” used along with, a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger frontal collision, the Supplemental Restraint System consists of air bag modules (located in the center steering wheel.
And in the instrument panel on the passenger side), seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness, spiral cable, the vehicle (except Crew Cab model) is equipped with a passenger air bag deactivation switch, rear seat exists where a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a rear-facing child restraint can be used in the front passenger seat, located in the center of the instrument panel, near the ashtray.
Position, the passenger air bag is disabled and will not inflate in a frontal collision, indicator on the instrument panel lights up when the passenger air bag is switched OFF, always remains enabled and is not affected by the passenger air bag deactivation switch, information necessary to service the system safely is included in the RS section Service Manual.
¼ To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, ¼ Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, ¼ The vehicle (except Crew Cab model) is equipped with a passenger air bag deactivation switch, which can be operated by the customer.
Switched ON, the passenger air bag is enabled and could inflate in a frontal collision, maintenance or repair, make sure the passenger air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived service, use a scraper to remove all traces of old liquid gasket, apply a continuous bead of liquid gasket mating surfaces.
(Use Genuine Silicone RTV or equivalent, for oil pan, be sure liquid gasket diameter is 3, for areas except oil pan, be sure liquid gasket diameter 2, apply liquid gasket around the inner side bolt holes (unless.
Assembly should be done within 5 minutes after coating, wait at least 30 minutes before refilling engine oil engine, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, pressing the tube liquid gasket.
A/T models, put selector lever Park P” position, if difference is extreme, check oil passage oil pump, install oil pressure switch with sealant, always replace with new oil seal gasket.
When removing oil pump, turn crankshaft so that No, when installing oil pump, apply engine oil gears, then, align punch mark on drive spindle and oil hole oil, visually inspect components wear damage.
Check oil pressure regulator valve sliding surface valve, coat regulator valve with engine oil, smoothly into the valve hole by its own weight, replace regulator valve set or oil pump assembly, damaged.
¼ Use Tool KV10115801 (J38956) removing oil filter, using a feeler gauge, check following clearances, outer rotor body clearance 2, if body to rotor clearances (2, 3) exceed limit, replace.
Regulator valve to oil pump cover clearance, adapting radiator cap tester radiator filler neck, ¼ Never remove the radiator cap when engine hot, serious burns could occur high pressure coolant.
¼ Wrap a thick cloth around the radiator cap, a quarter turn to allow built-up pressure to escape, check radiator for mud or clogging.
Nissan Models