2010 Nissan Cube - Steering System (Section ST) (21 pages)
Download Steering System (Section ST)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 3, service Notice or Precautions Steering System, steering Wheel Axial End Play Play20.
Socket Swing Force Rotating Torque20, outer/inner socket ball joint swinging torque, outer/inner socket ball joint rotating torque, outer/inner socket ball joint end play.
NVH in FAX, RAX, FSU, RSU section, improper installation or looseness steering column, improper installation or looseness tilt lock lever, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Use the chart below to find the cause of the symptom, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along C, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position.
In case of removing steering gear assembly, make the final tightening with grounded unloaded vehicle, condition, and then check wheel alignment, observe the following precautions when disassembling, - Before disassembly, thoroughly clean the outside unit.
- Disassembly should be done in a clean work area, contaminated by dirt other foreign matter, - For easier and proper assembly, place disassembled parts in order parts rack, - Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with.
- Before assembling, apply the specified grease directed parts, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, torque, pinion rotating torque and ball joint rotating torque, check installation conditions of steering gear assembly, front suspension assembly, axle steering column assembly.
Check if movement exists when steering wheel is moved up and down, to the left and right axial, check the following items when steering wheel axial end play is out standard, check the steering column assembly mounting condition.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 3, service Notice or Precautions Steering System, steering Wheel Axial End Play Play20.
Socket Swing Force Rotating Torque20, outer/inner socket ball joint swinging torque, outer/inner socket ball joint rotating torque, outer/inner socket ball joint end play.
NVH in FAX, RAX, FSU, RSU section, improper installation or looseness steering column, improper installation or looseness tilt lock lever, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Use the chart below to find the cause of the symptom, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along C, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position.
In case of removing steering gear assembly, make the final tightening with grounded unloaded vehicle, condition, and then check wheel alignment, observe the following precautions when disassembling, - Before disassembly, thoroughly clean the outside unit.
- Disassembly should be done in a clean work area, contaminated by dirt other foreign matter, - For easier and proper assembly, place disassembled parts in order parts rack, - Use nylon cloth or paper towels to clean the parts; common shop rags can leave lint that might interfere with.
- Before assembling, apply the specified grease directed parts, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, torque, pinion rotating torque and ball joint rotating torque, check installation conditions of steering gear assembly, front suspension assembly, axle steering column assembly.
Check if movement exists when steering wheel is moved up and down, to the left and right axial, check the following items when steering wheel axial end play is out standard, check the steering column assembly mounting condition.
Nissan Models