2010 Nissan Cube - Engine Mechanical (Section EM) (123 pages)
Download Engine Mechanical (Section EM)
Manual Description
Precaution for Procedure without Cowl Top Cover 5, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 5, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 5, dRIVE BELT AUTO TENSIONER AND IDLER.
FUEL INJECTOR AND FUEL TUBE 35, aIR CLEANER AND AIR DUCT 24, iGNITION COIL, SPARK PLUG AND ROCKER COVER 40, vALVE OIL SEAL : Removal Installation 62.
FRONT OIL SEAL : Removal Installation 63, rEAR OIL SEAL : Removal Installation 63, hOW TO SELECT PISTON AND BEARING 106, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Locate the area where noise occurs, specify the operating condition engine, if necessary, repair replace these parts, a: Closely related B: Related C: Sometimes related.
Precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc, precaution Necessary for Steering Wheel Rotation after Battery Disconnect.
Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged, turn the push-button ignition switch ACC position, (At this time, the steering lock will be released.
When the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Drain engine coolant and engine oil when engine cooled, before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
When instructed to use SST, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, dowel pins are used for several parts alignment.
Manual Description
Precaution for Procedure without Cowl Top Cover 5, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 5, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 5, dRIVE BELT AUTO TENSIONER AND IDLER.
FUEL INJECTOR AND FUEL TUBE 35, aIR CLEANER AND AIR DUCT 24, iGNITION COIL, SPARK PLUG AND ROCKER COVER 40, vALVE OIL SEAL : Removal Installation 62.
FRONT OIL SEAL : Removal Installation 63, rEAR OIL SEAL : Removal Installation 63, hOW TO SELECT PISTON AND BEARING 106, nOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING.
Locate the area where noise occurs, specify the operating condition engine, if necessary, repair replace these parts, a: Closely related B: Related C: Sometimes related.
Precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc, precaution Necessary for Steering Wheel Rotation after Battery Disconnect.
Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged, turn the push-button ignition switch ACC position, (At this time, the steering lock will be released.
When the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Drain engine coolant and engine oil when engine cooled, before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
When instructed to use SST, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, dowel pins are used for several parts alignment.
Nissan Models