2010 Nissan Cube - Emission Control System (Section EC) (476 pages)
Download Emission Control System (Section EC)
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 8, bASIC INSPECTION : Special Repair Requirement 13, cONTROL UNIT : Special Repair Requirement 16, iDLE AIR VOLUME LEARNING : Description18.
IDLE AIR VOLUME LEARNING : Special Repair, vIN REGISTRATION : Special Repair Requirement 17, lEARNING : Special Repair Requirement 18, tHROTTLE VALVE CLOSED POSITION LEARNING 18.
IDLE SPEED : Special Repair Requirement 17, iGNITION TIMING : Special Repair Requirement 17, a/F SENSOR 1 HEATER 127, iVT CONTROL SOLENOID VALVE 133.
ON BOARD DIAGNOSTIC (OBD) SYSTEM 86, pOWER SUPPLY AND GROUND CIRCUIT 117, fUEL INJECTION SYSTEM FUNCTION 204, fUEL INJECTION SYSTEM FUNCTION 200.
Component Inspection (Fuel filler cap)249, component Inspection (Fuel filler cap) 292, eVAP CONTROL SYSTEM PRESSURE SENSOR 267, eVAP CONTROL SYSTEM PRESSURE SENSOR 270.
EVAP CONTROL SYSTEM PRESSURE SENSOR 275, component Inspection (ASCD Brake Switch) 348, component Inspection (ASCD Clutch Switch) 349, component Inspection (Stop Lamp Switch) 349.
ASCD VEHICLE SPEED SENSOR 351, component Inspection (Stop Lamp Switch) 356, tHROTTLE CONTROL MOTOR RELAY 358, oN BOARD REFUELING VAPOR RECOVERY (ORVR) 408.
Component Inspection (Refueling EVAP vapor cut, wiring Diagram — ENGINE CONTROL SYSTEM, how to Erase Permanent DTC 449, test Value Test Limit 452.
Component Inspection (Ignition Coil with Power, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 464, precaution for Procedure without Cowl Top Cover, on Board Diagnosis (OBD) System Engine.
DIAGNOSIS AND REPAIR WORK FLOW, include trip freeze frame data, get the detailed information from the customer about the symptom (the condition environment, when the incident/malfunction occurred) using the Diagnostic Work Sheet”.
Ask if the customer requests I/M examination, no malfunction information, but a request for I/M examination>>GO TO 13, perform the following procedure DTC displayed, record DTC and freeze frame data.
Study the relationship between the cause detected by DTC and the symptom described by customer, are any symptoms described any DTCs detected, symptom is described, DTC detected>>GO TO 3, symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC detected>>GO TO 5, try to confirm the symptom described by the customer (except MIL ON), also study the normal operation and fail-safe related to the symptom, diagnosis Work Sheet is useful verify incident.
Verify relation between the symptom and the condition when symptom detected, try to confirm the symptom described by customer, perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then make sure that DTC.
Manual Description
DIAGNOSIS AND REPAIR WORK FLOW 8, bASIC INSPECTION : Special Repair Requirement 13, cONTROL UNIT : Special Repair Requirement 16, iDLE AIR VOLUME LEARNING : Description18.
IDLE AIR VOLUME LEARNING : Special Repair, vIN REGISTRATION : Special Repair Requirement 17, lEARNING : Special Repair Requirement 18, tHROTTLE VALVE CLOSED POSITION LEARNING 18.
IDLE SPEED : Special Repair Requirement 17, iGNITION TIMING : Special Repair Requirement 17, a/F SENSOR 1 HEATER 127, iVT CONTROL SOLENOID VALVE 133.
ON BOARD DIAGNOSTIC (OBD) SYSTEM 86, pOWER SUPPLY AND GROUND CIRCUIT 117, fUEL INJECTION SYSTEM FUNCTION 204, fUEL INJECTION SYSTEM FUNCTION 200.
Component Inspection (Fuel filler cap)249, component Inspection (Fuel filler cap) 292, eVAP CONTROL SYSTEM PRESSURE SENSOR 267, eVAP CONTROL SYSTEM PRESSURE SENSOR 270.
EVAP CONTROL SYSTEM PRESSURE SENSOR 275, component Inspection (ASCD Brake Switch) 348, component Inspection (ASCD Clutch Switch) 349, component Inspection (Stop Lamp Switch) 349.
ASCD VEHICLE SPEED SENSOR 351, component Inspection (Stop Lamp Switch) 356, tHROTTLE CONTROL MOTOR RELAY 358, oN BOARD REFUELING VAPOR RECOVERY (ORVR) 408.
Component Inspection (Refueling EVAP vapor cut, wiring Diagram — ENGINE CONTROL SYSTEM, how to Erase Permanent DTC 449, test Value Test Limit 452.
Component Inspection (Ignition Coil with Power, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 464, precaution for Procedure without Cowl Top Cover, on Board Diagnosis (OBD) System Engine.
DIAGNOSIS AND REPAIR WORK FLOW, include trip freeze frame data, get the detailed information from the customer about the symptom (the condition environment, when the incident/malfunction occurred) using the Diagnostic Work Sheet”.
Ask if the customer requests I/M examination, no malfunction information, but a request for I/M examination>>GO TO 13, perform the following procedure DTC displayed, record DTC and freeze frame data.
Study the relationship between the cause detected by DTC and the symptom described by customer, are any symptoms described any DTCs detected, symptom is described, DTC detected>>GO TO 3, symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC detected>>GO TO 5, try to confirm the symptom described by the customer (except MIL ON), also study the normal operation and fail-safe related to the symptom, diagnosis Work Sheet is useful verify incident.
Verify relation between the symptom and the condition when symptom detected, try to confirm the symptom described by customer, perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then make sure that DTC.
Nissan Models