2008 Nissan Armada - Fuel System (Section FL) (17 pages)
Download Fuel System (Section FL)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, fUEL LEVEL SENSOR UNIT, FUEL FILTER, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
When replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign workshop, be sure to work in a well ventilated area and furnish workshop with CO2 fire extinguisher, do not smoke while servicing fuel system.
Before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely, - Release fuel pressure from the fuel lines, - Disconnect battery negative terminal.
Always replace O-rings and clamps with new ones, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact any, after installing tubes, make sure there is no fuel leakage.
- Apply fuel pressure to fuel lines with turning ignition switch, - Start the engine and rev it up and check for fuel leaks connections, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery (ORVR)”, parts, refer to EC-480, "How to Detect Fuel Vapor Leakage", the actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here.
Removing and installing fuel tank lock ring, inspect fuel lines, fuel filler cap and fuel tank for improper attachment, leaks, cracks, damage, loose connections, chafing deterioration, if necessary, repair replace damaged parts, fuel level sensor, fuel filter, fuel 5.
Fuel level sensor, fuel filter, fuel, follow the General Precautions” before working on the fuel system, position the vehicle so it level, more than the level as shown (full or almost full), drain fuel.
From the fuel tank until the fuel gauge indicates level, if the fuel pump does not operate, use following procedure, to drain the fuel to the specified level after disconnecting, fuel filler hose from fuel filler pipe.
The fuel filler pipe through the fuel filler opening drain fuel, hose to drain the fuel fuel tank, liters US gal, 3 1/8 Imp gal) of fuel are drained fuel tank, remove the LH rear wheel and tire.
Remove the four clips and remove the fuel filler pipe shield, release the fuel pressure from the fuel lines, remove the second row LH rear seat and the third row rear seat, remove the second and third row rear seat belt buckles mounted on the floor.
And Installation of Second Row Seat Belt", SB-8, "Removal and Installation of Third Row Seat Belt", remove the LH center pillar trim, the LH rear trim panel, and the LH rear side door kick plate weather, remove the second row rear center console and base.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, fUEL LEVEL SENSOR UNIT, FUEL FILTER, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
When replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign workshop, be sure to work in a well ventilated area and furnish workshop with CO2 fire extinguisher, do not smoke while servicing fuel system.
Before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely, - Release fuel pressure from the fuel lines, - Disconnect battery negative terminal.
Always replace O-rings and clamps with new ones, after connecting the fuel tube quick connectors, make sure, ensure that the connector and resin tube do not contact any, after installing tubes, make sure there is no fuel leakage.
- Apply fuel pressure to fuel lines with turning ignition switch, - Start the engine and rev it up and check for fuel leaks connections, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, for servicing On Board Refueling Vapor Recovery (ORVR)”, parts, refer to EC-480, "How to Detect Fuel Vapor Leakage", the actual shapes of the Kent-Moore tools may differ from those of the special tools illustrated here.
Removing and installing fuel tank lock ring, inspect fuel lines, fuel filler cap and fuel tank for improper attachment, leaks, cracks, damage, loose connections, chafing deterioration, if necessary, repair replace damaged parts, fuel level sensor, fuel filter, fuel 5.
Fuel level sensor, fuel filter, fuel, follow the General Precautions” before working on the fuel system, position the vehicle so it level, more than the level as shown (full or almost full), drain fuel.
From the fuel tank until the fuel gauge indicates level, if the fuel pump does not operate, use following procedure, to drain the fuel to the specified level after disconnecting, fuel filler hose from fuel filler pipe.
The fuel filler pipe through the fuel filler opening drain fuel, hose to drain the fuel fuel tank, liters US gal, 3 1/8 Imp gal) of fuel are drained fuel tank, remove the LH rear wheel and tire.
Remove the four clips and remove the fuel filler pipe shield, release the fuel pressure from the fuel lines, remove the second row LH rear seat and the third row rear seat, remove the second and third row rear seat belt buckles mounted on the floor.
And Installation of Second Row Seat Belt", SB-8, "Removal and Installation of Third Row Seat Belt", remove the LH center pillar trim, the LH rear trim panel, and the LH rear side door kick plate weather, remove the second row rear center console and base.
Nissan Models