2013 Nissan Altima - Wiper Washer (Section WW) (66 pages)
Download Wiper Washer (Section WW)
Manual Description
Wiring Diagram - With Rear View Camera Washer, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 3, fRONT WIPER AND WASHER SYSTEM 4.
FRONT WIPER MOTOR LO CIRCUIT 34, fRONT WIPER MOTOR HI CIRCUIT 36, cOMMON ITEM : CONSULT Function (BCM COMMON ITEM) 10, fRONT WIPER AUTO STOP SIGNAL CIRCUIT 38.
WIPER : CONSULT Function (BCM - WIPER) 11, fRONT WIPER MOTOR GROUND CIRCUIT 39, wiring Diagram - Without Rear View Camera, fRONT WIPER DOES NOT OPERATE 48.
WASHER TUBE : Removal Installation 56, wIPER BLADE : Removal Installation 59, wIPER BLADE REFILL : Removal Installation, wASHER NOZZLE : Removal Installation 54.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover.
When performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc, fRONT WIPER AND WASHER SYSTEM, combination switch (wiper wash- 5.
Unit* (with rear trunk finisher removed), front wiper motor (with the wiper cowl re- 6, *: For models with rear camera washer system, transmits the vehicle speed signal to BCM with CAN communication.
Judges the switch status by the combination switch reading function, requests (with CAN communication) the front wiper relay and front wiper high, controls the integrated relay according to the request (with CAN communication), performs the auto stop control front wiper.
Supplies power to the rear view camera washer control unit, provides input for wiper and washer control BCM, supplies signal to the rear view camera washer control unit, washer fluid is sprayed according combination switch signal.
IPDM E/R controls front wiper operation, front wiper stop position is transmitted IPDM E/R, rear view camera washer control unit, (with rear view camera wash system).
Judges the signal status from the combination switch washer operation, supplies signal to front washer motor, sYSTEM WITH REAR VIEW CAMERA WASH, sYSTEM WITHOUT REAR VIEW CAMERA WASH.
The front wiper is controlled by each function of BCM IPDM E/R, bCM detects the combination switch condition by the combination switch reading function, bCM transmits the front wiper request signal to IPDM E/R with CAN communication depending each.
Manual Description
Wiring Diagram - With Rear View Camera Washer, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution for Procedure without Cowl Top Cover 3, fRONT WIPER AND WASHER SYSTEM 4.
FRONT WIPER MOTOR LO CIRCUIT 34, fRONT WIPER MOTOR HI CIRCUIT 36, cOMMON ITEM : CONSULT Function (BCM COMMON ITEM) 10, fRONT WIPER AUTO STOP SIGNAL CIRCUIT 38.
WIPER : CONSULT Function (BCM - WIPER) 11, fRONT WIPER MOTOR GROUND CIRCUIT 39, wiring Diagram - Without Rear View Camera, fRONT WIPER DOES NOT OPERATE 48.
WASHER TUBE : Removal Installation 56, wIPER BLADE : Removal Installation 59, wIPER BLADE REFILL : Removal Installation, wASHER NOZZLE : Removal Installation 54.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least 3 minutes before performing any service, precaution for Procedure without Cowl Top Cover.
When performing the procedure after removing cowl top cover, cover, the lower end of windshield with urethane, etc, fRONT WIPER AND WASHER SYSTEM, combination switch (wiper wash- 5.
Unit* (with rear trunk finisher removed), front wiper motor (with the wiper cowl re- 6, *: For models with rear camera washer system, transmits the vehicle speed signal to BCM with CAN communication.
Judges the switch status by the combination switch reading function, requests (with CAN communication) the front wiper relay and front wiper high, controls the integrated relay according to the request (with CAN communication), performs the auto stop control front wiper.
Supplies power to the rear view camera washer control unit, provides input for wiper and washer control BCM, supplies signal to the rear view camera washer control unit, washer fluid is sprayed according combination switch signal.
IPDM E/R controls front wiper operation, front wiper stop position is transmitted IPDM E/R, rear view camera washer control unit, (with rear view camera wash system).
Judges the signal status from the combination switch washer operation, supplies signal to front washer motor, sYSTEM WITH REAR VIEW CAMERA WASH, sYSTEM WITHOUT REAR VIEW CAMERA WASH.
The front wiper is controlled by each function of BCM IPDM E/R, bCM detects the combination switch condition by the combination switch reading function, bCM transmits the front wiper request signal to IPDM E/R with CAN communication depending each.
Nissan Models