2009 Nissan Altima - Wiper Washer (Section WW) (121 pages)
Download Wiper Washer (Section WW)
Manual Description
FRONT WIPER MOTOR GROUND CIRCUIT 26, fRONT WIPER AND WASHER SYSTEM 27, fRONT WIPER AND WASHER SYSTEM 6, cOMMON ITEM : Diagnosis Description 11.
COMMON ITEM : CONSULT-III Function 11, wIPER : CONSULT - III Function 12, cONSULT - III Function (IPDM E/R) 16, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 84.
FRONT WIPER DOES NOT OPERATE 108, fRONT WIPER AUTO STOP SIGNAL CIRCUIT24, supplemental Restraint System (SRS) AIR BA, necessary for Steering Wheel Rotation After Battery Disconnect111.
FRONT WIPER BLADE REFILL : Removal, fRONT WIPER BLADE : Removal Installation115, fRONT WIPER ARMS : Removal Installation 116, fRONT WIPER DRIVE ASSEMBLY : Removal.
FRONT WASHER NOZZLE : Removal Installation 118, fRONT WASHER NOZZLE : Adjustment 119, wASHER TANK : Removal Installation 119, fRONT WASHER PUMP : Removal Installation 120.
FRONT WIPER AND WASHER SWITCH 121, get the detailed information from the customer about the symptom (the condition environment when, record DTC and freeze frame data (Print them out with CONSULT-III, study the relationship between the cause detected by DTC and the symptom described by customer.
Is any symptom described any DTC detected, symptom is described, DTC displayed>>GO TO 3, symptom is described, DTC is not displayed>>GO TO 4, symptom is not described, DTC displayed>>GO TO 5.
Confirm the symptom described by customer, connect CONSULT-III to the vehicle in DATA MONITOR” mode and check real time diagnosis results, verify relation between the symptom and the condition when symptom detected, connect CONSULT-III to the vehicle in DATA MONITOR ” mode and check real time diagnosis results.
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC detected again, at this time, always connect CONSULT-III to the vehicle, and check diagnostic results real time, if two or more DTCs are detected, refer to BCS-90, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected.
Perform Component Function Check if DTC Confirmation Procedure is not included Service Manual, simplified check procedure is an effective alternative though DTC cannot be detected during check, if the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure, detect malfunctioning system according to WW-108, "Diagnosis Procedure" based confirmed symptom.
In step and determine the trouble diagnosis order based on possible causes symptom, inspect according to Diagnostic Procedure system, the Diagnostic Procedure described based on open circuit inspection, required for the circuit check Diagnostic Procedure.
>> Check voltage of related BCM terminals using CONSULT-III, repair or replace malfunctioning part, reconnect parts or connectors disconnected during Diagnostic Procedure again after repair replacement, when DTC was detected in step 2, perform DTC Confirmation Procedure Component Function Check.
Again, and then check that the malfunction have been repaired securely, when symptom was described from the customer, refer to confirmed symptom in step 3 or 4, check that, yES (DTC detected)>>GO TO 8, fRONT WIPER AND WASHER SYSTEM.
The front wiper is controlled by each function of BCM IPDM E/R, bCM detects the combination switch condition by the combination switch reading function, bCM transmits the front wiper request signal to IPDM E/R with CAN communication depending each.
Manual Description
FRONT WIPER MOTOR GROUND CIRCUIT 26, fRONT WIPER AND WASHER SYSTEM 27, fRONT WIPER AND WASHER SYSTEM 6, cOMMON ITEM : Diagnosis Description 11.
COMMON ITEM : CONSULT-III Function 11, wIPER : CONSULT - III Function 12, cONSULT - III Function (IPDM E/R) 16, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 84.
FRONT WIPER DOES NOT OPERATE 108, fRONT WIPER AUTO STOP SIGNAL CIRCUIT24, supplemental Restraint System (SRS) AIR BA, necessary for Steering Wheel Rotation After Battery Disconnect111.
FRONT WIPER BLADE REFILL : Removal, fRONT WIPER BLADE : Removal Installation115, fRONT WIPER ARMS : Removal Installation 116, fRONT WIPER DRIVE ASSEMBLY : Removal.
FRONT WASHER NOZZLE : Removal Installation 118, fRONT WASHER NOZZLE : Adjustment 119, wASHER TANK : Removal Installation 119, fRONT WASHER PUMP : Removal Installation 120.
FRONT WIPER AND WASHER SWITCH 121, get the detailed information from the customer about the symptom (the condition environment when, record DTC and freeze frame data (Print them out with CONSULT-III, study the relationship between the cause detected by DTC and the symptom described by customer.
Is any symptom described any DTC detected, symptom is described, DTC displayed>>GO TO 3, symptom is described, DTC is not displayed>>GO TO 4, symptom is not described, DTC displayed>>GO TO 5.
Confirm the symptom described by customer, connect CONSULT-III to the vehicle in DATA MONITOR” mode and check real time diagnosis results, verify relation between the symptom and the condition when symptom detected, connect CONSULT-III to the vehicle in DATA MONITOR ” mode and check real time diagnosis results.
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC detected again, at this time, always connect CONSULT-III to the vehicle, and check diagnostic results real time, if two or more DTCs are detected, refer to BCS-90, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected.
Perform Component Function Check if DTC Confirmation Procedure is not included Service Manual, simplified check procedure is an effective alternative though DTC cannot be detected during check, if the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure, detect malfunctioning system according to WW-108, "Diagnosis Procedure" based confirmed symptom.
In step and determine the trouble diagnosis order based on possible causes symptom, inspect according to Diagnostic Procedure system, the Diagnostic Procedure described based on open circuit inspection, required for the circuit check Diagnostic Procedure.
>> Check voltage of related BCM terminals using CONSULT-III, repair or replace malfunctioning part, reconnect parts or connectors disconnected during Diagnostic Procedure again after repair replacement, when DTC was detected in step 2, perform DTC Confirmation Procedure Component Function Check.
Again, and then check that the malfunction have been repaired securely, when symptom was described from the customer, refer to confirmed symptom in step 3 or 4, check that, yES (DTC detected)>>GO TO 8, fRONT WIPER AND WASHER SYSTEM.
The front wiper is controlled by each function of BCM IPDM E/R, bCM detects the combination switch condition by the combination switch reading function, bCM transmits the front wiper request signal to IPDM E/R with CAN communication depending each.
Nissan Models