2009 Nissan Altima - Exhaust System (Section EX) (13 pages)
Download Exhaust System (Section EX)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, necessary for Steering Wheel Rotation After Battery Disconnect 2, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 8, necessary for Steering Wheel Rotation After Battery Disconnect 8.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, necessary for Steering Wheel Rotation After Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables.
After finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation, supply power using jumper cables battery discharged, carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch ACC position.
(At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position.
Perform self-diagnosis check of all control units using CONSULT-III, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening heated oxygen sensors, before installing a new oxygen sensor (Use.
Or equivalent meeting MIL specification MIL-A-907), check the exhaust pipes, muffler, mounting components, incorrect attachment, leaks, cracks, damage, deterioration, perform the procedure with the exhaust system fully cooled down because the system will be hot.
Just after the engine turned off, use genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tools, remove heated oxygen sensor using Tool needed.
Installation is in the reverse order removal, always replace exhaust gaskets with new ones when reassembling, before installing a new heated oxygen sensor, clean and lube the exhaust tube threads using suitable tool, oxygen sensor thread cleaner : — (J-43897-18).
Oxygen sensor thread cleaner : — (J-43897-12), discard any heated oxygen sensor which has been dropped from a height of more than 0, in) onto a hard surface such as a concrete floor; install new one, resulting in MIL coming on.
If any mounting insulator is badly deformed, repair or replace it, the mounting insulator, clean inspect them, when installing the insulator avoid large gaps or interference between insulator each, remove deposits from the sealing surface of each connection.
Temporarily tighten the exhaust manifold side nuts and the vehicle side bolts, any interference, and then tighten the nuts bolts specification, when installing each mounting rubber, avoid twisting or excessive extension up/down right.
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, necessary for Steering Wheel Rotation After Battery Disconnect 2, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 8, necessary for Steering Wheel Rotation After Battery Disconnect 8.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, necessary for Steering Wheel Rotation After Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables.
After finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation, supply power using jumper cables battery discharged, carry the Intelligent Key or insert it to the key slot and turn the push-button ignition switch ACC position.
(At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position, wheel will lock when the push-button ignition switch is turned LOCK position.
Perform self-diagnosis check of all control units using CONSULT-III, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening heated oxygen sensors, before installing a new oxygen sensor (Use.
Or equivalent meeting MIL specification MIL-A-907), check the exhaust pipes, muffler, mounting components, incorrect attachment, leaks, cracks, damage, deterioration, perform the procedure with the exhaust system fully cooled down because the system will be hot.
Just after the engine turned off, use genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tools, remove heated oxygen sensor using Tool needed.
Installation is in the reverse order removal, always replace exhaust gaskets with new ones when reassembling, before installing a new heated oxygen sensor, clean and lube the exhaust tube threads using suitable tool, oxygen sensor thread cleaner : — (J-43897-18).
Oxygen sensor thread cleaner : — (J-43897-12), discard any heated oxygen sensor which has been dropped from a height of more than 0, in) onto a hard surface such as a concrete floor; install new one, resulting in MIL coming on.
If any mounting insulator is badly deformed, repair or replace it, the mounting insulator, clean inspect them, when installing the insulator avoid large gaps or interference between insulator each, remove deposits from the sealing surface of each connection.
Temporarily tighten the exhaust manifold side nuts and the vehicle side bolts, any interference, and then tighten the nuts bolts specification, when installing each mounting rubber, avoid twisting or excessive extension up/down right.
Nissan Models