2009 Nissan Altima - Body Control System (Section BCS) (96 pages)
Download Body Control System (Section BCS)
Manual Description
CONTROL UNIT : Special Repair Requirement 5, cONFIGURATION (BCM) : Special Repair Requirement 6, cONFIGURATION (BCM) : Configuration list 7, dOOR LOCK : CONSULT-III Function (BCM DOOR LOCK)19.
MULTI REMOTE ENT : CONSULT-III Function, wIPER : CONSULT - III Function26, bCM : CONSULT-III Function (BCM - BCM)31, iMMU : CONSULT-III Function (BCM - IMMU)31.
BATTERY SAVER : CONSULT-III Function 32, tRUNK : CONSULT-III Function (BCM - TRUNK) 33, tHEFT ALM : CONSULT-III Function (BCM THEFT ALM) 33, rETAINED PWR : CONSULT-III Function (BCM RETAINED PWR) 34.
SIGNAL BUFFER : CONSULT-III Function 35, aIR PRESSURE MONITOR : Diagnosis Description 35, aIR PRESSURE MONITOR : CONSULT-III Function (BCM-AIR PRESSURE MONITOR) 37, pOWER SUPPLY AND GROUND CIRCUIT 42.
Supplemental Restraint System (SRS) "AIR B, aG" and "SEAT BELT PRE-TENSIONER" 95, necessary for Steering Wheel Rotation After Battery Disconnect 95, get the detailed information from the customer about the symptom (the condition environment when.
Record DTC freeze frame data, study the relationship between the cause detected by DTC and the symptom described by customer, is any symptom described any DTC detected, symptom is described, DTC displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4, symptom is not described, DTC displayed>>GO TO 5, confirm the symptom described by customer, connect CONSULT-III to the vehicle in DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when symptom detected, connect CONSULT-III to the vehicle in DATA MONITOR ” mode and check real time diagnosis results, perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC detected again, at this time, always connect CONSULT-III to the vehicle, and check diagnostic results real time.
If two or more DTCs are detected, refer to BCS-90, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected, perform Component Function Check if DTC Confirmation Procedure is not included Service Manual, simplified check procedure is an effective alternative though DTC cannot be detected during check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure, detect malfunctioning system according to BCS-8, "System Description" based on confirmed symptom, step and determine the trouble diagnosis order based on possible causes symptom, inspect according to Diagnostic Procedure system.
The Diagnostic Procedure described based on open circuit inspection, required for the circuit check Diagnostic Procedure, >> Check voltage of related BCM terminals using CONSULT-III, repair or replace malfunctioning part.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair replacement, when DTC was detected in step 2, perform DTC Confirmation Procedure Component Function Check, again, and then check that the malfunction has been repaired, when symptom was described from the customer, refer to confirmed symptom in step 3 or 4, check that.
YES (DTC detected)>>GO TO 8, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, when replacing BCM, save or print current vehicle specification with CONSULT-III configuration before.
If READ CONFIGURATION” can not be used, use the WRITE CONFIGURATION - Manual selection” after, when replacing BCM, you must perform WRITE CONFIGURATION” with CONSULT-III, - Complete the procedure of WRITE CONFIGURATION” order.
Manual Description
CONTROL UNIT : Special Repair Requirement 5, cONFIGURATION (BCM) : Special Repair Requirement 6, cONFIGURATION (BCM) : Configuration list 7, dOOR LOCK : CONSULT-III Function (BCM DOOR LOCK)19.
MULTI REMOTE ENT : CONSULT-III Function, wIPER : CONSULT - III Function26, bCM : CONSULT-III Function (BCM - BCM)31, iMMU : CONSULT-III Function (BCM - IMMU)31.
BATTERY SAVER : CONSULT-III Function 32, tRUNK : CONSULT-III Function (BCM - TRUNK) 33, tHEFT ALM : CONSULT-III Function (BCM THEFT ALM) 33, rETAINED PWR : CONSULT-III Function (BCM RETAINED PWR) 34.
SIGNAL BUFFER : CONSULT-III Function 35, aIR PRESSURE MONITOR : Diagnosis Description 35, aIR PRESSURE MONITOR : CONSULT-III Function (BCM-AIR PRESSURE MONITOR) 37, pOWER SUPPLY AND GROUND CIRCUIT 42.
Supplemental Restraint System (SRS) "AIR B, aG" and "SEAT BELT PRE-TENSIONER" 95, necessary for Steering Wheel Rotation After Battery Disconnect 95, get the detailed information from the customer about the symptom (the condition environment when.
Record DTC freeze frame data, study the relationship between the cause detected by DTC and the symptom described by customer, is any symptom described any DTC detected, symptom is described, DTC displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4, symptom is not described, DTC displayed>>GO TO 5, confirm the symptom described by customer, connect CONSULT-III to the vehicle in DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when symptom detected, connect CONSULT-III to the vehicle in DATA MONITOR ” mode and check real time diagnosis results, perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC detected again, at this time, always connect CONSULT-III to the vehicle, and check diagnostic results real time.
If two or more DTCs are detected, refer to BCS-90, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected, perform Component Function Check if DTC Confirmation Procedure is not included Service Manual, simplified check procedure is an effective alternative though DTC cannot be detected during check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure, detect malfunctioning system according to BCS-8, "System Description" based on confirmed symptom, step and determine the trouble diagnosis order based on possible causes symptom, inspect according to Diagnostic Procedure system.
The Diagnostic Procedure described based on open circuit inspection, required for the circuit check Diagnostic Procedure, >> Check voltage of related BCM terminals using CONSULT-III, repair or replace malfunctioning part.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair replacement, when DTC was detected in step 2, perform DTC Confirmation Procedure Component Function Check, again, and then check that the malfunction has been repaired, when symptom was described from the customer, refer to confirmed symptom in step 3 or 4, check that.
YES (DTC detected)>>GO TO 8, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description, when replacing BCM, save or print current vehicle specification with CONSULT-III configuration before.
If READ CONFIGURATION” can not be used, use the WRITE CONFIGURATION - Manual selection” after, when replacing BCM, you must perform WRITE CONFIGURATION” with CONSULT-III, - Complete the procedure of WRITE CONFIGURATION” order.
Nissan Models