2008 Nissan Altima - Fuel System (Section FL) (14 pages)
Download Fuel System (Section FL)
Manual Description
FUEL LEVEL SENSOR UNIT, FUEL FILTER, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
The actual shape of the Kent-Moore tools may differ from those tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, fuel filler cap and fuel tank for improper attachment, leaks, cracks, damage, loose connections, chafing deterioration, if necessary, repair replace damaged parts.
After connecting fuel tube quick connectors, make sure quick, ensure that connector and resin tube do not contact any adjacent parts, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area.
Be sure to work in a well ventilated area and have CO2 fire extinguisher, do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely.
- Release fuel pressure from the fuel lines, - Disconnect battery ground cable, always replace O-rings and clamps with new ones, do not tighten hose clamps excessively avoid damaging hoses.
Tighten high-pressure rubber hose clamp so that clamp end, tightening torque specifications are the same all rubber, ensure that screw does not contact adjacent parts, after connecting the fuel tube quick connectors, make sure.
Check that the connector and resin tube do not contact any, - a) Apply fuel pressure to the fuel system by turning the ignition switch to ON (without starting the engine), fuel leaks at fuel tube connections, - b) Start the engine and rev the engine, then check fuel.
Leaks at fuel tube connections, after installing the tubes, run the engine check fuel, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, "System Description" (QR25DE), EC-1084, "System, for servicing On Board Refueling Vapor Recovery (ORVR)”, parts, refer to EC-466, "Description" (QR25DE), EC-1444.
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY, fuel level sensor unit, fuel filter, read General Precautions” before working fuel system, the fuel pump inspection hole cover.
Disconnect the fuel level sensor, fuel filter, fuel pump, assembly electrical connector, EVAP hose quick connector, the fuel feed hose quick connector from fuel level sensor, unit, fuel filter, fuel pump assembly.
Remove the quick connector follows, hold the sides of the connector, push in tabs pull out, several times until they start to move.
Manual Description
FUEL LEVEL SENSOR UNIT, FUEL FILTER, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system.
The actual shape of the Kent-Moore tools may differ from those tools illustrated here, removing and installing fuel tank lock ring, inspect fuel lines, fuel filler cap and fuel tank for improper attachment, leaks, cracks, damage, loose connections, chafing deterioration, if necessary, repair replace damaged parts.
After connecting fuel tube quick connectors, make sure quick, ensure that connector and resin tube do not contact any adjacent parts, when replacing fuel line parts, be sure observe following, put a CAUTION: FLAMMABLE” sign work area.
Be sure to work in a well ventilated area and have CO2 fire extinguisher, do not smoke while working on the fuel system, before removing fuel line parts, carry out following procedures, - Put drained fuel in an explosion-proof container and put the lid on securely.
- Release fuel pressure from the fuel lines, - Disconnect battery ground cable, always replace O-rings and clamps with new ones, do not tighten hose clamps excessively avoid damaging hoses.
Tighten high-pressure rubber hose clamp so that clamp end, tightening torque specifications are the same all rubber, ensure that screw does not contact adjacent parts, after connecting the fuel tube quick connectors, make sure.
Check that the connector and resin tube do not contact any, - a) Apply fuel pressure to the fuel system by turning the ignition switch to ON (without starting the engine), fuel leaks at fuel tube connections, - b) Start the engine and rev the engine, then check fuel.
Leaks at fuel tube connections, after installing the tubes, run the engine check fuel, use only a Genuine NISSAN fuel filler cap replacement, an incorrect fuel filler cap is used, the MIL may come on.
For servicing Evaporative Emission System” parts, refer, "System Description" (QR25DE), EC-1084, "System, for servicing On Board Refueling Vapor Recovery (ORVR)”, parts, refer to EC-466, "Description" (QR25DE), EC-1444.
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY, fuel level sensor unit, fuel filter, read General Precautions” before working fuel system, the fuel pump inspection hole cover.
Disconnect the fuel level sensor, fuel filter, fuel pump, assembly electrical connector, EVAP hose quick connector, the fuel feed hose quick connector from fuel level sensor, unit, fuel filter, fuel pump assembly.
Remove the quick connector follows, hold the sides of the connector, push in tabs pull out, several times until they start to move.
Nissan Models