2005 Nissan 350Z - Engine Mechanical (Section EM) (184 pages)
Download Engine Mechanical (Section EM)
Manual Description
Precautions for Procedures without Cowl Top Cover 4, precautions for Drain Engine Coolant 4, precautions for Disconnecting Fuel Piping 4, precautions for Removal Disassembly 4.
Precautions for Inspection, Repair Replacement 4, precautions for Assembly Installation 4, rEMOVAL OF LIQUID GASKET SEALING 5, nVH Troubleshooting — Engine Noise 12.
Use the Chart Below to Help You Find Cause, aIR CLEANER AND AIR DUCT 16, eXHAUST MANIFOLD AND THREE WAY CATALYST 25, fUEL INJECTOR AND FUEL TUBE 38.
FRONT TIMING CHAIN CASE 47, removal and Installation (Except 35th Anniversary) 59, removal and Installation (For 35th Anniversary) 81, removal and Installation of Valve Oil Seal 117.
Removal and Installation of Front Oil Seal 118, removal and Installation of Rear Oil Seal 118, how to Select Piston Bearing 153, hOW TO SELECT CONNECTING ROD BEARING 154.
HOW TO SELECT MAIN BEARING 155, pISTON TO PISTON PIN OIL CLEARANCE 158, cONNECTING ROD BEND AND TORSION 160, cONNECTING ROD BIG END DIAMETER 161.
CONNECTING ROD BUSHING OIL CLEARANCE 161, cONNECTING ROD BEARING OIL CLEARANCE 165, cRUSH HEIGHT OF MAIN BEARING 166, mAIN BEARING CAP BOLT OUTER DIAMETER.
SERVICE DATA AND SPECIFICATIONS (SDS) 169, pISTON, PISTON RING AND PISTON PIN 177, precautions for Procedures without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc, before disconnecting the battery, lower both the driver and passenger windows, window slightly raises and lowers automatically to prevent any window to vehicle interference, window function will not work with battery disconnected.
Drain engine coolant when engine cooled, before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
When instructed to use special service tools, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials, mark and arrange disassembly parts in an organized way for easy troubleshooting re-assembly.
When loosening bolts and nuts, as a basic rule, start with the one furthest outside, then one diagonally, precautions for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts, use torque wrench to tighten bolts nuts specification.
When tightening bolts and nuts, as a basic rule, equally tighten in several different steps starting with, ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, dowel pins are used for several parts alignment.
Sure that dowel pins are installed original portion, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Manual Description
Precautions for Procedures without Cowl Top Cover 4, precautions for Drain Engine Coolant 4, precautions for Disconnecting Fuel Piping 4, precautions for Removal Disassembly 4.
Precautions for Inspection, Repair Replacement 4, precautions for Assembly Installation 4, rEMOVAL OF LIQUID GASKET SEALING 5, nVH Troubleshooting — Engine Noise 12.
Use the Chart Below to Help You Find Cause, aIR CLEANER AND AIR DUCT 16, eXHAUST MANIFOLD AND THREE WAY CATALYST 25, fUEL INJECTOR AND FUEL TUBE 38.
FRONT TIMING CHAIN CASE 47, removal and Installation (Except 35th Anniversary) 59, removal and Installation (For 35th Anniversary) 81, removal and Installation of Valve Oil Seal 117.
Removal and Installation of Front Oil Seal 118, removal and Installation of Rear Oil Seal 118, how to Select Piston Bearing 153, hOW TO SELECT CONNECTING ROD BEARING 154.
HOW TO SELECT MAIN BEARING 155, pISTON TO PISTON PIN OIL CLEARANCE 158, cONNECTING ROD BEND AND TORSION 160, cONNECTING ROD BIG END DIAMETER 161.
CONNECTING ROD BUSHING OIL CLEARANCE 161, cONNECTING ROD BEARING OIL CLEARANCE 165, cRUSH HEIGHT OF MAIN BEARING 166, mAIN BEARING CAP BOLT OUTER DIAMETER.
SERVICE DATA AND SPECIFICATIONS (SDS) 169, pISTON, PISTON RING AND PISTON PIN 177, precautions for Procedures without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc, before disconnecting the battery, lower both the driver and passenger windows, window slightly raises and lowers automatically to prevent any window to vehicle interference, window function will not work with battery disconnected.
Drain engine coolant when engine cooled, before starting work, make sure no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
When instructed to use special service tools, use specified tools, exercise maximum care to avoid damage to mating sliding surfaces, cover openings of engine system with tape or equivalent, if necessary, to seal out foreign materials, mark and arrange disassembly parts in an organized way for easy troubleshooting re-assembly.
When loosening bolts and nuts, as a basic rule, start with the one furthest outside, then one diagonally, precautions for Inspection, Repair Replacement, before repairing or replacing, thoroughly inspect parts, use torque wrench to tighten bolts nuts specification.
When tightening bolts and nuts, as a basic rule, equally tighten in several different steps starting with, ones in center, then ones on inside and outside diagonally in this order, replace with new gasket, packing, oil seal O-ring, dowel pins are used for several parts alignment.
Sure that dowel pins are installed original portion, thoroughly wash, clean, and air-blow each part, avoid damaging sliding or mating surfaces.
Nissan Models