2015 Infiniti QX80/QX - Interior Lighting System (Section INL) (84 pages)
Download Interior Lighting System (Section INL)
Manual Description
COMMON ITEM : CONSULT Function (BCM COMMON ITEM)12, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3, iNT LAMP : CONSULT Function (BCM - INT.
BATTERY SAVER : CONSULT Function (BCM BATTERY SAVER)15, iNTERIOR ROOM LAMP CONTROL SYSTEM 6, iNTERIOR ROOM LAMP CONTROL SYSTEM , iNTERIOR ROOM LAMP BATTERY SAVER SYSTEM 8.
AUTO LIGHT ADJUSTMENT SYSTEM : System, dIAGNOSIS AND REPAIR WORK FLOW 54, pASSENGER SIDE : Exploded View 73, rEAR FOOT LAMP : Exploded View 74.
REAR FOOT LAMP : Removal Installation 74, pUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT 67, fRONT DOOR ARMREST : Exploded View 77, fRONT DOOR ARMREST : Replacement 77.
REAR DOOR ARMREST : Exploded View 77, rEAR DOOR ARMREST : Replacement 78, dRIVER SIDE : Exploded View 73, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, when removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may.
For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC.
The removal of 12V battery may cause DTC detection error, side) (door key cylinder switch, unlock sensor), controls the integrated relay according to the request signal from BCM (via CAN communication), refer to "DOOR LOCK SYSTEM : Component Description".
Receives the dimmer signal from BCM via CAN communication, detects door lock condition driver side door, refer to "COMBINATION SWITCH READING SYSTEM : System Description", inputs the lock/unlock signal BCM.
Inputs the door switch signal BCM, iNTERIOR ROOM LAMP CONTROL SYSTEM : System Diagram, iNTERIOR ROOM LAMP CONTROL SYSTEM : System Description, interior room lamps* are controlled by interior room lamp timer control function BCM.
*: Map lamp, foot lamp and personal lamp (when map lamp switch and personal lamp switch DOOR, step lamp is controlled by step lamp control function BCM, luggage room lamp and automatic back door close switch illumination are controlled by luggage room lamp.
Manual Description
COMMON ITEM : CONSULT Function (BCM COMMON ITEM)12, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precautions for Removing Battery Terminal 3, iNT LAMP : CONSULT Function (BCM - INT.
BATTERY SAVER : CONSULT Function (BCM BATTERY SAVER)15, iNTERIOR ROOM LAMP CONTROL SYSTEM 6, iNTERIOR ROOM LAMP CONTROL SYSTEM , iNTERIOR ROOM LAMP BATTERY SAVER SYSTEM 8.
AUTO LIGHT ADJUSTMENT SYSTEM : System, dIAGNOSIS AND REPAIR WORK FLOW 54, pASSENGER SIDE : Exploded View 73, rEAR FOOT LAMP : Exploded View 74.
REAR FOOT LAMP : Removal Installation 74, pUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT 67, fRONT DOOR ARMREST : Exploded View 77, fRONT DOOR ARMREST : Replacement 77.
REAR DOOR ARMREST : Exploded View 77, rEAR DOOR ARMREST : Replacement 78, dRIVER SIDE : Exploded View 73, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, when removing the 12V battery terminal, turn OFF ignition, switch and wait least 30 seconds, stops, then a DTC detection error or ECU data corruption may.
For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON ignition switch, if the ignition switch is turned ON with any one terminals, main battery and sub battery disconnected, then DTC may be, after installing the 12V battery, always check "Self Diagnosis Result" of all ECUs erase DTC.
The removal of 12V battery may cause DTC detection error, side) (door key cylinder switch, unlock sensor), controls the integrated relay according to the request signal from BCM (via CAN communication), refer to "DOOR LOCK SYSTEM : Component Description".
Receives the dimmer signal from BCM via CAN communication, detects door lock condition driver side door, refer to "COMBINATION SWITCH READING SYSTEM : System Description", inputs the lock/unlock signal BCM.
Inputs the door switch signal BCM, iNTERIOR ROOM LAMP CONTROL SYSTEM : System Diagram, iNTERIOR ROOM LAMP CONTROL SYSTEM : System Description, interior room lamps* are controlled by interior room lamp timer control function BCM.
*: Map lamp, foot lamp and personal lamp (when map lamp switch and personal lamp switch DOOR, step lamp is controlled by step lamp control function BCM, luggage room lamp and automatic back door close switch illumination are controlled by luggage room lamp.
Read(view) online free pdf manual 2015 Infiniti QX80/QX
Infiniti Models