2015 Infiniti QX60 - Exhaust System (Section EX) (6 pages)
Download Exhaust System (Section EX)
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
One front air bag, depending on the severity of a collision and whether the front passenger seat occupied, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least three minutes before performing any service, check exhaust pipes, muffler and mounts improper attachment, perform the procedures with the exhaust system fully cooled down to avoid injury hot.
Use Genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tool, installation is in the reverse order removal, exhaust Manifold Exhaust Front Tube.
Install the seal bearing (2) into the front exhaust tube (1), when installing the spring (3) and nut (4), ensure following, - Make sure the spring (3) sits properly on flange surface by, aligning it to locator dimples (A).
- Make sure the stud (5) does not contact the inside flange, be careful not to damage seal bearing surface when installing, compact spring by tightening nut, ensure springs are seated correctly on the flange and not sitting locator dimples (A).
Assemble the seal bearing so that the nut is located in the center of the flare flange hole without, do not reuse exhaust gaskets, temporarily tighten the nuts on the exhaust manifold side and the bolts on vehicle side, each part for interference with other components, and then tighten the nuts bolts specification.
With the engine running, check the exhaust tube joints for exhaust gas leaks unusual noises, check that the mount brackets and mount insulators are installed properly and free excessive stress, improper installation could result in excessive noise, leaks, vibration...
Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
One front air bag, depending on the severity of a collision and whether the front passenger seat occupied, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least three minutes before performing any service, check exhaust pipes, muffler and mounts improper attachment, perform the procedures with the exhaust system fully cooled down to avoid injury hot.
Use Genuine NISSAN exhaust system parts or equivalent, which are specifically designed heat, remove exhaust system components using power tool, installation is in the reverse order removal, exhaust Manifold Exhaust Front Tube.
Install the seal bearing (2) into the front exhaust tube (1), when installing the spring (3) and nut (4), ensure following, - Make sure the spring (3) sits properly on flange surface by, aligning it to locator dimples (A).
- Make sure the stud (5) does not contact the inside flange, be careful not to damage seal bearing surface when installing, compact spring by tightening nut, ensure springs are seated correctly on the flange and not sitting locator dimples (A).
Assemble the seal bearing so that the nut is located in the center of the flare flange hole without, do not reuse exhaust gaskets, temporarily tighten the nuts on the exhaust manifold side and the bolts on vehicle side, each part for interference with other components, and then tighten the nuts bolts specification.
With the engine running, check the exhaust tube joints for exhaust gas leaks unusual noises, check that the mount brackets and mount insulators are installed properly and free excessive stress, improper installation could result in excessive noise, leaks, vibration...
Read(view) online free pdf manual 2015 Infiniti QX60
Infiniti Models