2011 Infiniti QX56 - Engine Mechanical (Section EM) (142 pages)
Download Engine Mechanical (Section EM)
Manual Description
Use the Chart Below to Help You Find C, precaution for Procedure without Cowl Top Cover 3, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 3.
Precaution for Drain Engine Coolant Engine, precaution for Disconnecting Fuel Piping 4, precaution for Handling High Pressure Fuel System 4, precaution for Removal Disassembly 4.
Precaution for Inspection, Repair Replacement 4, precaution for Assembly Installation 4, dRIVE BELT AUTO TENSIONER AND IDLER, aIR CLEANER AND AIR DUCT 27.
NVH Troubleshooting - Engine Noise 18, hIGH PRESSURE FUEL PUMP AND FUEL, fRONT OIL SEAL : Removal Installation 96, rEAR OIL SEAL : Removal Installation 97.
FUEL INJECTOR AND FUEL TUBE 48, hOW TO SELECT PISTON AND BEARING 125, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position.
Wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III, precaution for Drain Engine Coolant Engine Oil, drain engine coolant and engine oil when engine cooled.
Before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
Manual Description
Use the Chart Below to Help You Find C, precaution for Procedure without Cowl Top Cover 3, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, precaution Necessary for Steering Wheel Rotation after Battery Disconnect 3.
Precaution for Drain Engine Coolant Engine, precaution for Disconnecting Fuel Piping 4, precaution for Handling High Pressure Fuel System 4, precaution for Removal Disassembly 4.
Precaution for Inspection, Repair Replacement 4, precaution for Assembly Installation 4, dRIVE BELT AUTO TENSIONER AND IDLER, aIR CLEANER AND AIR DUCT 27.
NVH Troubleshooting - Engine Noise 18, hIGH PRESSURE FUEL PUMP AND FUEL, fRONT OIL SEAL : Removal Installation 96, rEAR OIL SEAL : Removal Installation 97.
FUEL INJECTOR AND FUEL TUBE 48, hOW TO SELECT PISTON AND BEARING 125, precaution for Procedure without Cowl Top Cover, when performing the procedure after removing cowl top cover, cover.
The lower end of windshield with urethane, etc, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, module, see SRS AIR BAG”.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s), when using air or electric power tools or hammers, always switch the ignition OFF, disconnect.
Battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation after Battery Disconnect, before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both.
Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the push-button ignition switch ACC position, (At this time, the steering lock will be released, when the repair work is completed, re-connect both battery cables, the push-button ignition switch from ACC position to ON position, then to LOCK position.
Wheel will lock when the push-button ignition switch is turned LOCK position, perform self-diagnosis check of all control units using CONSULT-III, precaution for Drain Engine Coolant Engine Oil, drain engine coolant and engine oil when engine cooled.
Before starting work, check no fire or spark producing items are work area, release fuel pressure before disconnecting disassembly, after disconnecting pipes, plug openings stop fuel leakage.
Read(view) online free pdf manual 2011 Infiniti QX56
Infiniti Models