2006 Infiniti QX56 - Wiper Washer (Section WW) (56 pages)
Download Wiper Washer (Section WW)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, fRONT WIPER AND WASHER SYSTEM 4, components Parts and Harness Connector Location 4, wiring Diagram — WIPER — 8.
Terminals and Reference Values BCM11, terminals and Reference Values IPDM E/R 12, front Wiper Does Not Operate 18, fRONT WIPER STOP POSITION IS INCORRECT 21.
ONLY FRONT WIPER LOW DOES NOT OPERATE 22, oNLY FRONT WIPER HIGH DOES NOT OPER, sWITCH POSITION CANNOT BE ADJUSTED 26, wIPERS DO NOT WIPE WHEN FRONT.
FRONT WIPERS OPERATE FOR 10 SECONDS, STOP FOR 20 SECONDS, AND AFTER, rEAR WIPER AND WASHER SYSTEM 32, components Parts and Harness Connector Location 32, bCM WIPER SWITCH READING FUNCTION 35.
Wiring Diagram — WIP/R — 36, terminals and Reference Values BCM 38, how to Proceed With Trouble Diagnosis 40, rear Wiper Does Not Operate 44.
Rear Wiper Stop Position Is Incorrect 46, only Rear Wiper Does Not Operate 47, only Rear Wiper Intermittent Does Not Operate 48, wiper Does Not Wipe When Rear Washer Operates 48.
Front Power Socket LH, Rear Cargo Power Socket54, front Power Socket RH (For Cigarette Lighter), precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, fRONT WIPER AND WASHER SYSTEM.
Components Parts Harness Connector Location, front and rear washer motor connector, both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room), the wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
BCM controls front wiper LO, HI, INT (intermittent) operation, iPDM E/R (intelligent power distribution module engine room) operates the wiper motor according CAN, power is supplied all times, through fusible link (letter f , located in the fuse fusible link box).
To front wiper relay (located IPDM E/R), with the ignition switch in ON or START position, power supplied, to combination switch terminal 14, to IPDM E/R terminals 38 59.
To front wiper motor terminal 1, when the ignition switch is in the ON or START position, and the front wiper switch is turned to the low position, the BCM detects a low speed wiper ON request through the combination switch (wiper switch) reading, from BCM terminals 39 40, to IPDM E/R terminals 39 40.
When IPDM E/R receives front wiper (low) request signal, it supplies ground to energize front wiper relay, with the front wiper relay energized, power supplied, to front wiper motor terminal 3.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 3, fRONT WIPER AND WASHER SYSTEM 4, components Parts and Harness Connector Location 4, wiring Diagram — WIPER — 8.
Terminals and Reference Values BCM11, terminals and Reference Values IPDM E/R 12, front Wiper Does Not Operate 18, fRONT WIPER STOP POSITION IS INCORRECT 21.
ONLY FRONT WIPER LOW DOES NOT OPERATE 22, oNLY FRONT WIPER HIGH DOES NOT OPER, sWITCH POSITION CANNOT BE ADJUSTED 26, wIPERS DO NOT WIPE WHEN FRONT.
FRONT WIPERS OPERATE FOR 10 SECONDS, STOP FOR 20 SECONDS, AND AFTER, rEAR WIPER AND WASHER SYSTEM 32, components Parts and Harness Connector Location 32, bCM WIPER SWITCH READING FUNCTION 35.
Wiring Diagram — WIP/R — 36, terminals and Reference Values BCM 38, how to Proceed With Trouble Diagnosis 40, rear Wiper Does Not Operate 44.
Rear Wiper Stop Position Is Incorrect 46, only Rear Wiper Does Not Operate 47, only Rear Wiper Intermittent Does Not Operate 48, wiper Does Not Wipe When Rear Washer Operates 48.
Front Power Socket LH, Rear Cargo Power Socket54, front Power Socket RH (For Cigarette Lighter), precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, fRONT WIPER AND WASHER SYSTEM.
Components Parts Harness Connector Location, front and rear washer motor connector, both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room), the wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
BCM controls front wiper LO, HI, INT (intermittent) operation, iPDM E/R (intelligent power distribution module engine room) operates the wiper motor according CAN, power is supplied all times, through fusible link (letter f , located in the fuse fusible link box).
To front wiper relay (located IPDM E/R), with the ignition switch in ON or START position, power supplied, to combination switch terminal 14, to IPDM E/R terminals 38 59.
To front wiper motor terminal 1, when the ignition switch is in the ON or START position, and the front wiper switch is turned to the low position, the BCM detects a low speed wiper ON request through the combination switch (wiper switch) reading, from BCM terminals 39 40, to IPDM E/R terminals 39 40.
When IPDM E/R receives front wiper (low) request signal, it supplies ground to energize front wiper relay, with the front wiper relay energized, power supplied, to front wiper motor terminal 3.
Read(view) online free pdf manual 2006 Infiniti QX56
Infiniti Models