2006 Infiniti QX56 - Enging Cooling System (Section CO) (24 pages)
Download Enging Cooling System (Section CO)
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, rEMOVAL OF LIQUID GASKET SEALING 2, cHECKING COOLING SYSTEM FOR LEAKS 10, removal and Installation (Crankshaft Driven Type) 17.
Removal and Installation (Motor Driven Type) 18, sERVICE DATA AND SPECIFICATIONS (SDS) 23, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, after removing the bolts and nuts, separate mating surface.
And remove the old liquid gasket sealing using Tool, do not damage mating surfaces, tap the seal cutter insert it, in areas where the Tool is difficult to use, lightly tap slide it.
Remove the old liquid gasket adhering gasket application, surface and the mating surface using suitable tool, q Remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes.
Thoroughly clean the mating surfaces remove adhering, attach the liquid gasket tube Tool, use Genuine RTV Silicone Sealant equivalent, apply the liquid gasket without breaks specified location.
If there is a groove for the liquid gasket application, apply, q Within five minutes of liquid gasket application, install mating component, q If the liquid gasket protrudes, wipe it off immediately, q Do not retighten after installation.
Q Wait minutes or more after installation before refilling, engine with engine oil engine coolant, if there are specific instructions in manual, observe them, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Removing steel oil pan rear timing chain, pressing the tube liquid gasket, adapting radiator cap tester radiator cap, adapting radiator cap tester reservoir filler.
Adapting radiator cap tester reservoir cap, o-ring for damage, deterioration improper fitting, check if the engine coolant reservoir tank level within MIN, mAX level when engine cool.
Adjust engine coolant level necessary, never remove the radiator or reservoir cap when the engine is hot, high-pressure engine coolant escaping from radiator reservoir, to check for leakage, apply pressure to cooling system.
The reservoir filler neck using suitable tool Tool, higher pressure than specified may cause radiator damage, in case that engine coolant decreases, replenish cooling system, if any concerns are found, repair replace damaged parts.
Check reservoir cap relief pressure using suitable tool Tool, apply engine coolant cap seal, replace the reservoir cap if there is any damage in the negative-pressure valve, or if the open-valve pressure outside.
Manual Description
(SRS) AIR BAG” and SEAT BELT PRE-TENSIONER” 2, rEMOVAL OF LIQUID GASKET SEALING 2, cHECKING COOLING SYSTEM FOR LEAKS 10, removal and Installation (Crankshaft Driven Type) 17.
Removal and Installation (Motor Driven Type) 18, sERVICE DATA AND SPECIFICATIONS (SDS) 23, precautions for Supplemental Restraint System (SRS) AIR BAG” SEAT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.
With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury death, improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system, do not use electrical test equipment on any circuit related to the SRS unless instructed, after removing the bolts and nuts, separate mating surface.
And remove the old liquid gasket sealing using Tool, do not damage mating surfaces, tap the seal cutter insert it, in areas where the Tool is difficult to use, lightly tap slide it.
Remove the old liquid gasket adhering gasket application, surface and the mating surface using suitable tool, q Remove the liquid gasket completely from groove, liquid gasket application surface, bolts, bolt holes.
Thoroughly clean the mating surfaces remove adhering, attach the liquid gasket tube Tool, use Genuine RTV Silicone Sealant equivalent, apply the liquid gasket without breaks specified location.
If there is a groove for the liquid gasket application, apply, q Within five minutes of liquid gasket application, install mating component, q If the liquid gasket protrudes, wipe it off immediately, q Do not retighten after installation.
Q Wait minutes or more after installation before refilling, engine with engine oil engine coolant, if there are specific instructions in manual, observe them, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Removing steel oil pan rear timing chain, pressing the tube liquid gasket, adapting radiator cap tester radiator cap, adapting radiator cap tester reservoir filler.
Adapting radiator cap tester reservoir cap, o-ring for damage, deterioration improper fitting, check if the engine coolant reservoir tank level within MIN, mAX level when engine cool.
Adjust engine coolant level necessary, never remove the radiator or reservoir cap when the engine is hot, high-pressure engine coolant escaping from radiator reservoir, to check for leakage, apply pressure to cooling system.
The reservoir filler neck using suitable tool Tool, higher pressure than specified may cause radiator damage, in case that engine coolant decreases, replenish cooling system, if any concerns are found, repair replace damaged parts.
Check reservoir cap relief pressure using suitable tool Tool, apply engine coolant cap seal, replace the reservoir cap if there is any damage in the negative-pressure valve, or if the open-valve pressure outside.
Read(view) online free pdf manual 2006 Infiniti QX56
Infiniti Models