2011 Infiniti FX - Instrument Panel (Section IP) (26 pages)
Download Instrument Panel (Section IP)
Manual Description
SQUEAK AND RATTLE TROUBLE DIAGNOSES 6, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precautions Necessary for Steering Wheel Rotation After Battery Disconnection 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection, comply with the following cautions to prevent any error malfunction, before removing and installing any control units, first turn the ignition switch LOCK position, after finishing work, confirm that all control unit connectors are connected properly, then re-connect.
Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the ignition switch ACC position, (At this time, the steering lock will be released, the ignition switch from ACC position to ON position, then to LOCK position, when the ignition switch is turned LOCK position.
Disconnect battery negative terminal advance, disconnect air bag system line advance, never tamper with or force air bag lid open, as this may adversely affect air bag performance, be careful not to scratch pad other parts.
When removing or disassembling any part, be careful not to damage or deform it, when removing parts with a screwdriver or other tool, cover the tool surface by vinyl tape protect parts, keep removed parts protected with shop cloth, if an unreusable part is removed, replace it with new one.
Tighten bolts and nuts firmly specified torque, after reassembly has been completed, make sure each part functions correctly, dip a soft cloth in warm water, and then squeeze it tightly, dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then clean off stain with.
Then wipe the area with soft dry cloth, never use any organic solvent, such thinner benzine, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removes clips, pawls metal clips.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, customer's comments; refer to IP-10, "Diagnostic Worksheet", conditions that exist when noise occurs.
All the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, perform a diagnosis and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics.
Manual Description
SQUEAK AND RATTLE TROUBLE DIAGNOSES 6, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precautions Necessary for Steering Wheel Rotation After Battery Disconnection 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.
The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted.
Information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”, always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with, ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service.
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection, comply with the following cautions to prevent any error malfunction, before removing and installing any control units, first turn the ignition switch LOCK position, after finishing work, confirm that all control unit connectors are connected properly, then re-connect.
Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing, for vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock, if turning the steering wheel is required with the battery disconnected or discharged, follow the operation procedure below before starting repair operation, supply power using jumper cables battery discharged.
Turn the ignition switch ACC position, (At this time, the steering lock will be released, the ignition switch from ACC position to ON position, then to LOCK position, when the ignition switch is turned LOCK position.
Disconnect battery negative terminal advance, disconnect air bag system line advance, never tamper with or force air bag lid open, as this may adversely affect air bag performance, be careful not to scratch pad other parts.
When removing or disassembling any part, be careful not to damage or deform it, when removing parts with a screwdriver or other tool, cover the tool surface by vinyl tape protect parts, keep removed parts protected with shop cloth, if an unreusable part is removed, replace it with new one.
Tighten bolts and nuts firmly specified torque, after reassembly has been completed, make sure each part functions correctly, dip a soft cloth in warm water, and then squeeze it tightly, dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then clean off stain with.
Then wipe the area with soft dry cloth, never use any organic solvent, such thinner benzine, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removes clips, pawls metal clips.
SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, customer's comments; refer to IP-10, "Diagnostic Worksheet", conditions that exist when noise occurs.
All the facts and conditions that exist when the noise occurs (or does not occur), if there is more than one noise in the vehicle, perform a diagnosis and repair the noise that customer, after identifying the type of noise, isolate the noise in terms of its characteristics.
Read(view) online free pdf manual 2011 Infiniti FX
Infiniti Models