2010 Infiniti FX - Exterior Lighting System (Section EXL) (246 pages)
Download Exterior Lighting System (Section EXL)
Manual Description
CONTROL UNIT : Special Repair Requirement 7, lEVELIZER ADJUSTMENT : Special Repair Requirement 7, eXTERIOR LAMP BATTERY SAVER SYSTEM 30, cOMMON ITEM : CONSULT-III Function (BCM COMMON ITEM)32.
HEADLAMP : CONSULT-III Function (BCM HEAD LAMP)33, fLASHER : CONSULT-III Function (BCM FLASHER) 35, pOWER SUPPLY AND GROUND CIRCUIT 63, bCM (BODY CONTROL MODULE) : Diagnosis.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 63, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Diagnosis Procedure 63, aFS CONTROL UNIT : Diagnosis Procedure 64, hEIGHT SENSOR UNUSUAL [RR] 50.
SHIFT SIGNAL [P, R] 53, sTEERING ANGLE SENSOR SIGNAL 59, sTEERING ANGLE SENSOR CALIBRATION 60, wiring Diagram - ACTIVE AFS - 202.
Wiring Diagram - HEADLAMP - 91, wiring Diagram - AUTO LIGHT SYSTEM - 97, wiring Diagram - HEADLAMP AIMING CONTROL SYSTEM (MANUAL) - 105, wiring Diagram - DAYTIME LIGHT SYSTEM - 109.
Wiring Diagram - FRONT FOG LAMP - 116, wiring Diagram - TURN AND HAZARD WARNING LAMPS - 122, bOTH SIDE HEADLAMPS DO NOT SWITCH, bOTH SIDE HEADLAMPS (LO) ARE NOT.
LAMPS ARE NOT TURNED ON 220, bOTH SIDE FRONT FOG LAMPS ARE NOT, wiring Diagram - PARKING LICENSE PLATE, wiring Diagram - STOP LAMP - 139.
Wiring Diagram - BACK-UP LAMP - 146, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 222, precautions For Xenon Headlamp Service 222, wiring Diagram - BCM - 174.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 186, wiring Diagram - IPDM E/R - 193, lIGHTING & TURN SIGNAL SWITCH 234, check the symptom customer's information.
Check the operation of each part, perform the trouble diagnosis for the detected DTC, check that the symptom is applied fail-safe activation, perform the system diagnosis for the system that the fail-safe activates.
Repair or replace malfunctioning part, check the operation each part, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description.
Perform LEVELIZER ADJUSTMENT” with CONSULT-III when replacing height sensor, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, >> Refer to EXL-7, "LEVELIZER ADJUSTMENT : Special Repair Requirement", perform LEVELIZER ADJUSTMENT” when installing, removing, and replacing the height sensor suspension components.
LEVELIZER ADJUSTMENT : Special Repair Requirement, park the vehicle straight-forward position, unload the vehicle (no passenger aboard), select "LEVELIZER ADJUSTMENT" of ADAPTIVE LIGHT work support item.
When "ADJUSTMENT IS COMPLETED", select "END", if "CAN NOT BE TESTED" is indicated, AFS control unit detects that the height sensor signal EXL, >> Perform levelizer adjustment again.
Manual Description
CONTROL UNIT : Special Repair Requirement 7, lEVELIZER ADJUSTMENT : Special Repair Requirement 7, eXTERIOR LAMP BATTERY SAVER SYSTEM 30, cOMMON ITEM : CONSULT-III Function (BCM COMMON ITEM)32.
HEADLAMP : CONSULT-III Function (BCM HEAD LAMP)33, fLASHER : CONSULT-III Function (BCM FLASHER) 35, pOWER SUPPLY AND GROUND CIRCUIT 63, bCM (BODY CONTROL MODULE) : Diagnosis.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 63, iPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) : Diagnosis Procedure 63, aFS CONTROL UNIT : Diagnosis Procedure 64, hEIGHT SENSOR UNUSUAL [RR] 50.
SHIFT SIGNAL [P, R] 53, sTEERING ANGLE SENSOR SIGNAL 59, sTEERING ANGLE SENSOR CALIBRATION 60, wiring Diagram - ACTIVE AFS - 202.
Wiring Diagram - HEADLAMP - 91, wiring Diagram - AUTO LIGHT SYSTEM - 97, wiring Diagram - HEADLAMP AIMING CONTROL SYSTEM (MANUAL) - 105, wiring Diagram - DAYTIME LIGHT SYSTEM - 109.
Wiring Diagram - FRONT FOG LAMP - 116, wiring Diagram - TURN AND HAZARD WARNING LAMPS - 122, bOTH SIDE HEADLAMPS DO NOT SWITCH, bOTH SIDE HEADLAMPS (LO) ARE NOT.
LAMPS ARE NOT TURNED ON 220, bOTH SIDE FRONT FOG LAMPS ARE NOT, wiring Diagram - PARKING LICENSE PLATE, wiring Diagram - STOP LAMP - 139.
Wiring Diagram - BACK-UP LAMP - 146, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 222, precautions For Xenon Headlamp Service 222, wiring Diagram - BCM - 174.
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) 186, wiring Diagram - IPDM E/R - 193, lIGHTING & TURN SIGNAL SWITCH 234, check the symptom customer's information.
Check the operation of each part, perform the trouble diagnosis for the detected DTC, check that the symptom is applied fail-safe activation, perform the system diagnosis for the system that the fail-safe activates.
Repair or replace malfunctioning part, check the operation each part, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description.
Perform LEVELIZER ADJUSTMENT” with CONSULT-III when replacing height sensor, aDDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement, >> Refer to EXL-7, "LEVELIZER ADJUSTMENT : Special Repair Requirement", perform LEVELIZER ADJUSTMENT” when installing, removing, and replacing the height sensor suspension components.
LEVELIZER ADJUSTMENT : Special Repair Requirement, park the vehicle straight-forward position, unload the vehicle (no passenger aboard), select "LEVELIZER ADJUSTMENT" of ADAPTIVE LIGHT work support item.
When "ADJUSTMENT IS COMPLETED", select "END", if "CAN NOT BE TESTED" is indicated, AFS control unit detects that the height sensor signal EXL, >> Perform levelizer adjustment again.
Read(view) online free pdf manual 2010 Infiniti FX
Infiniti Models