2008 Infiniti EX35 - Front Axle (Section FAX) (32 pages)
Download Front Axle (Section FAX)
Manual Description
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"10, precaution Necessary for Steering Wheel Rotation after Battery Disconnect10, fRONT WHEEL HUB AND KNUCKLE 5, fRONT WHEEL HUB AND KNUCKLE 14.
FRONT WHEEL HUB AND KNUCKLE 6, fRONT WHEEL HUB AND KNUCKLE 16, wHEEL SIDE : Removal Installation19, fINAL DRIVE SIDE : Removal Installation22.
LEFT SIDE : Removal Installation24, rIGHT SIDE : Removal Installation 24, wHEEL SIDE : Disassembly Assembly 25, fINAL DRIVE SIDE : Disassembly Assembly 27.
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, refer to DRIVE SHAFT chart, use chart below to help you find the cause of the symptom, fRONT WHEEL HUB AND KNUCKLE.
Make sure that the mounting conditions (looseness, backlash) of each component component conditions, move wheel hub and bearing assembly in the axial direction by hand, rotate wheel hub and make sure that is no unusual noise or other irregular conditions, irregular conditions, replace wheel hub bearing assembly.
Refer to "Components" for symbols figure, remove wheel sensor and sensor harness, never pull wheel sensor harness, never depress brake pedal while brake caliper removed.
Temporarily tighten the nut to prevent damage to threads and to prevent ball joint remover, note the following, and install in the reverse order removal, perform the final tightening of each of parts under unladen conditions, which were removed when removing, wheel hub and bearing assembly steering knuckle.
Check components for deformation, cracks, and other damage, check boots of transverse link and steering outer socket ball joint for breakage, axial play, torque, "Inspection" and ST-33, "2WD : Inspection", check wheel sensor harness for proper connection.
Adjust neutral position of steering angle sensor, sENSOR NEUTRAL POSITION : Special Repair Requirement", sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS).
Refer to Front axle chart, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIRBAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, precaution Necessary for Steering Wheel Rotation after Battery Disconnect.
Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation.
Manual Description
(SRS) "AIR BAG" "SEAT BELT PRE-TENSIONER"10, precaution Necessary for Steering Wheel Rotation after Battery Disconnect10, fRONT WHEEL HUB AND KNUCKLE 5, fRONT WHEEL HUB AND KNUCKLE 14.
FRONT WHEEL HUB AND KNUCKLE 6, fRONT WHEEL HUB AND KNUCKLE 16, wHEEL SIDE : Removal Installation19, fINAL DRIVE SIDE : Removal Installation22.
LEFT SIDE : Removal Installation24, rIGHT SIDE : Removal Installation 24, wHEEL SIDE : Disassembly Assembly 25, fINAL DRIVE SIDE : Disassembly Assembly 27.
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING, refer to DRIVE SHAFT chart, use chart below to help you find the cause of the symptom, fRONT WHEEL HUB AND KNUCKLE.
Make sure that the mounting conditions (looseness, backlash) of each component component conditions, move wheel hub and bearing assembly in the axial direction by hand, rotate wheel hub and make sure that is no unusual noise or other irregular conditions, irregular conditions, replace wheel hub bearing assembly.
Refer to "Components" for symbols figure, remove wheel sensor and sensor harness, never pull wheel sensor harness, never depress brake pedal while brake caliper removed.
Temporarily tighten the nut to prevent damage to threads and to prevent ball joint remover, note the following, and install in the reverse order removal, perform the final tightening of each of parts under unladen conditions, which were removed when removing, wheel hub and bearing assembly steering knuckle.
Check components for deformation, cracks, and other damage, check boots of transverse link and steering outer socket ball joint for breakage, axial play, torque, "Inspection" and ST-33, "2WD : Inspection", check wheel sensor harness for proper connection.
Adjust neutral position of steering angle sensor, sENSOR NEUTRAL POSITION : Special Repair Requirement", sERVICE DATA AND SPECIFICATIONS (SDS), < SERVICE DATA AND SPECIFICATIONS (SDS).
Refer to Front axle chart, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain.
System uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIRBAG” and SEAT BELT”, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.
The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, precaution Necessary for Steering Wheel Rotation after Battery Disconnect.
Before removing and installing any control units, first turn the push-button ignition switch to the LOCK position, then disconnect both battery cables, after finishing work, confirm that all control unit connectors are connected properly, then re-connect both, always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, this vehicle is equipped with a push-button ignition switch and steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock cannot be turned, if turning the steering wheel is required with the battery disconnected or discharged, follow procedure, below before starting repair operation.
Read(view) online free pdf manual 2008 Infiniti EX35
Infiniti Models