2008 Infiniti EX35 - Emission Control System (Section EC) (543 pages)
Download Emission Control System (Section EC)
Manual Description
BASIC INSPECTION : Special Repair Requirement 12, cONTROL UNIT : Special Repair Requirement 15, iDLE SPEED : Special Repair Requirement 16, iGNITION TIMING : Special Repair Requirement 16.
VIN REGISTRATION : Special Repair Requirement 17, lEARNING : Special Repair Requirement 17, iDLE AIR VOLUME LEARNING : Description17, iDLE AIR VOLUME LEARNING : Special Repair.
EXHAUST VALVE TIMING CONTROL LEARNING : Description19, eXHAUST VALVE TIMING CONTROL LEARNING : Special Repair Requirement19, tHROTTLE VALVE CLOSED POSITION LEARNING 17, oN BOARD DIAGNOSTIC (OBD) SYSTEM 100.
POWER SUPPLY AND GROUND CIRCUIT 133, eVT CONTROL MAGNET RETARDER 154, eVAP CONTROL SYSTEM PRESSURE SENSOR 297, eVAP CONTROL SYSTEM PRESSURE SENSOR 302.
EVAP CONTROL SYSTEM PRESSURE SENSOR 294, eLECTRIC THROTTLE CONTROL FUNCTION 360, eLECTRIC THROTTLE CONTROL ACTUATOR 367, component Inspection (Stop Lamp Switch) 419.
Component Inspection (ICC Brake Hold Relay)412, component Inspection (ASCD Brake Switch) 440, component Inspection (Cooling Fan Motor) 445, component Inspection (Cooling Fan Relay) 446.
ICC VEHICLE SPEED SENSOR 415, aSCD VEHICLE SPEED SENSOR 413, component Inspection (ICC Brake Switch) 456, component Inspection (Ignition Coil with Power.
Test Value Test Limit 520, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 531, precaution for Procedure without Cowl Top Cover 531, precautions For Xenon Headlamp Service 531.
On Board Diagnostic (OBD) System Engine, wiring Diagram - ENGINE CONTROL SYSTEM - 493, oN BOARD REFUELING VAPOR RECOVERY (ORVR) 464, get the detailed information from the customer about the symptom (the condition environment when.
The incident/malfunction occurred) using the Diagnostic Work Sheet”, perform the following procedure DTC displayed, record DTC and freeze frame data, study the relationship between the cause detected by DTC and the symptom described by customer.
Is any symptom described and any DTC detected, symptom is described, DTC detected>>GO TO 3, symptom is described, DTC is not detected>>GO TO 4, symptom is not described, DTC detected>>GO TO 5.
Try to confirm the symptom described by the customer (except MIL ON), also study the normal operation and fail safe related to the symptom, diagnosis Work Sheet is useful verify incident, verify relation between the symptom and the condition when symptom detected.
Try to confirm the symptom described by customer, perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then check that DTC detected, if two or more DTCs are detected, refer to EC-512, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected.
Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included Service, if the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIRMATION PROCEDURE, >> Check according GI-38, "Intermittent Incident".
Manual Description
BASIC INSPECTION : Special Repair Requirement 12, cONTROL UNIT : Special Repair Requirement 15, iDLE SPEED : Special Repair Requirement 16, iGNITION TIMING : Special Repair Requirement 16.
VIN REGISTRATION : Special Repair Requirement 17, lEARNING : Special Repair Requirement 17, iDLE AIR VOLUME LEARNING : Description17, iDLE AIR VOLUME LEARNING : Special Repair.
EXHAUST VALVE TIMING CONTROL LEARNING : Description19, eXHAUST VALVE TIMING CONTROL LEARNING : Special Repair Requirement19, tHROTTLE VALVE CLOSED POSITION LEARNING 17, oN BOARD DIAGNOSTIC (OBD) SYSTEM 100.
POWER SUPPLY AND GROUND CIRCUIT 133, eVT CONTROL MAGNET RETARDER 154, eVAP CONTROL SYSTEM PRESSURE SENSOR 297, eVAP CONTROL SYSTEM PRESSURE SENSOR 302.
EVAP CONTROL SYSTEM PRESSURE SENSOR 294, eLECTRIC THROTTLE CONTROL FUNCTION 360, eLECTRIC THROTTLE CONTROL ACTUATOR 367, component Inspection (Stop Lamp Switch) 419.
Component Inspection (ICC Brake Hold Relay)412, component Inspection (ASCD Brake Switch) 440, component Inspection (Cooling Fan Motor) 445, component Inspection (Cooling Fan Relay) 446.
ICC VEHICLE SPEED SENSOR 415, aSCD VEHICLE SPEED SENSOR 413, component Inspection (ICC Brake Switch) 456, component Inspection (Ignition Coil with Power.
Test Value Test Limit 520, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 531, precaution for Procedure without Cowl Top Cover 531, precautions For Xenon Headlamp Service 531.
On Board Diagnostic (OBD) System Engine, wiring Diagram - ENGINE CONTROL SYSTEM - 493, oN BOARD REFUELING VAPOR RECOVERY (ORVR) 464, get the detailed information from the customer about the symptom (the condition environment when.
The incident/malfunction occurred) using the Diagnostic Work Sheet”, perform the following procedure DTC displayed, record DTC and freeze frame data, study the relationship between the cause detected by DTC and the symptom described by customer.
Is any symptom described and any DTC detected, symptom is described, DTC detected>>GO TO 3, symptom is described, DTC is not detected>>GO TO 4, symptom is not described, DTC detected>>GO TO 5.
Try to confirm the symptom described by the customer (except MIL ON), also study the normal operation and fail safe related to the symptom, diagnosis Work Sheet is useful verify incident, verify relation between the symptom and the condition when symptom detected.
Try to confirm the symptom described by customer, perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then check that DTC detected, if two or more DTCs are detected, refer to EC-512, "DTC Inspection Priority Chart" determine trouble, freeze frame data is useful if the DTC not detected.
Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included Service, if the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIRMATION PROCEDURE, >> Check according GI-38, "Intermittent Incident".
Read(view) online free pdf manual 2008 Infiniti EX35
Infiniti Models